Abstract:Thermal spray cermet based on tungsten carbide has been widely used due to its excellent wear resistance. The features of both carbide and binder phases are essential factors which determine the performance of cermet coating. The thermal cycling of WC–Co spray particles up to a temperature over the melting point of binder phase during thermal spraying involves the decarburization of carbide. The decarburization of carbide becomes severe with the decrease of carbide particle size, which makes it difficult yet to deposit a dense nanostructured WC–Co with a limited decarburization by thermal spraying. The decarburization not only reduces the wear-resistant phase but also leads to the formation of brittle Co–W–C ternary binder phase. Moreover, the limited decarburization involves the deposition of spray particle at a solid–liquid two-phase state with carbides at a solid state and metal binder in a molten state during spraying. High velocity impact of two-phase droplets as in high velocity oxy-fuel spraying (HVOF) results in the formation of a dense cermet coating and on the other hand leads to the possibility of rebounding of wear-resistant solid carbide particles. In this review article, the microstructural features of thermal spray WC–Co are examined based on the effect of the decarburization of tungsten carbide. The decarburization mechanisms of tungsten carbide are discussed for the control of decarburization of carbide. The effects of carbide particle size on the deposition process, adhesion of HVOF coating and wear performance of WC–Co coating as well are examined based on a solid–liquid two-phase deposition process. It is demonstrated that WC–Co cermet with different sizes of WC particles should be deposited by different processes. Moreover, the deposition of nanostructured WC–Co by thermal spraying and recent advances on the cold spraying of nanostructured WC–Co are introduced. The cold spraying with the proper design of spray powders will become promising process to deposit nanostructured WC–Co with pure cobalt binder with the hardness comparable to a sintered bulk and even high toughness of 18.9MPam1/2. The pure metastable metal binder phase evolved in the deposit makes it possible to deposit hard cermet through healing the non-bonded interfaces in the coating by post-spray annealing.

Influence of Substrate Hardness on Deposition Behavior of Single Porous Wc-12co Particle in Cold Spraying

Influence of Substrate Hardness on Deposition Behavior of Single Porous WC-12Co Particles in Cold Spraying

Influence of Powder Porous Structure on the Deposition Behavior of Cold-Sprayed Wc-12co Coatings

Influence of Substrate Hardness Transition on Built-Up of Nanostructured WC–12Co by Cold Spraying

Influence of Powder Structure on the Micro-Hardness and Fracture Toughness of Cold-Sprayed WC-12Co Deposit

Characterization of Nano-Structured WC-Co Deposited by Cold Spraying

Relationships Between Feedstock Structure, Particle Parameter, Coating Deposition, Microstructure and Properties for Thermally Sprayed Conventional and Nanostructured WC–Co

Toughening of Cold-Sprayed Nanostructured WC-12Co Deposit Through Using Multimodal WC Particles and Annealing

Preparation And Properties Of Cold Sprayed Nano Wc-17co Coating On Magnesium Alloy

Effect of the Powder Particle Structure and Substrate Hardness During Vacuum Cold Spraying of Al2O3

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

Correlation study of random deposition for WC–12Co multiparticles on the TC18 substrates

Cold Spray Deposition of a Core-Shell Structured WC-Co Coating

Mechanical Property and Wear Performance Dependence on Processing Condition for Cold-Sprayed WC-(nanoWC-Co)

Effects Of Wc Crystal Characteristics On Microstructure And Mechanical Property Of Hvof-Sprayed Wc-Cocr Coatings

Influence of WC Particle Size on the Mechanical Properties and Residual Stress of HVOF Thermally Sprayed WC–10Co–4Cr Coatings

WC-Co Composite Coating Deposited by Cold Spraying of a Core-Shell-Structured WC-Co Powder

Comparison of the Mechanical and Electrochemical Properties of WC-25Co Coatings Obtained by High Velocity Oxy-Fuel and Cold Gas Spraying

Effect of the substrate surface and coating powder hardness on the formation of a cold sprayed composite layer

Effect of types of ceramic materials in aggregated powder on the adhesive strength of high velocity oxy-fuel sprayed cermet coatings

Microstructure and wear behaviors of a WC10%-Ni60AA cermet coating synthesized by laser-directed energy deposition