Abstract:Melt-spun Al 75− X Si 25 Ni X ( X = 2, 4, 7, and 10 mol%) alloys were investigated as anode materials for lithium-ion batteries. The Al 68 Si 25 Ni 7 anode showed a maximum capacity of 840 mA h g −1 at the fifth cycle and maintained 661 mA h g −1 after 40 cycles with a high coulumbic efficiency of 93%. The specific capacity increased as the decrease in the Ni content during the first 20 cycles, but the cycle performance became poorer. For the Al 65 Si 25 Ni 10 anode, the specific capacity increased slowly as the cycles increased and reached 370 mA h g −1 after 40 cycles. When the Al 68 Si 25 Ni 7 ribbons were annealed, their initial capacity became higher, but much poorer cycle performance and low coulumbic efficiency occurred. Except Al 65 Si 25 Ni 10, the AlLi compound could be detected in the anodes after lithiation. However, the capacity faded rapidly due to the formation of excessive AlLi in the Al 73 Si 25 Ni 2 and annealed Al 68 Si 25 Ni 7 anodes. The experiments revealed that the as-quenched ribbons consisted of the nanoscaled α-Al, metallic glass and α-Si, and their fractions were dependent on the Ni content. The α-Al was a supersaturated solid solution of Si and Ni in fcc-Al. For the as-quenched Al 68 Si 25 Ni 7 ribbons, the α-Al grains were embedded in the amorphous matrix. It can be understood that metallic glass can store Li, and the supersaturated solid solution can store Li even more easily compared with other known Al–Si-based alloys. A conclusion can be drawn that the microstructure that the nanoscaled α-Al embedded in the metallic glass matrix is beneficial to improve the structure stability, restrain serious structural evolution, and limit the volume variation and pulverization during electrochemical cycles.

Effects of Cr Content on Electrochemical Properties of Melt-Spun Al75-xSi25Crx Alloy Anodes for Lithium-Ion Batteries

Effects of the phase constitution and microstructure on the electrochemical properties of melt-spun Al 882XSi 12MnX anode materials for lithium-ion batteries

Effects of the phase constitution and microstructure on the electrochemical properties of melt-spun Al88−X Si12Mn X anode materials for lithium-ion batteries

Investigation of crack patterns and cyclic performance of Ti-Si nanocomposite thin film anodes for lithium ion batteries

The Electrochemical Properties of Melt-Spun Al–Si–Cu Alloys

The electrochemical properties of Al–Si–Ni alloys composed of nanocrystal and metallic glass for lithium-ion battery anodes

Effects of the phase constitution and microstructure on the electrochemical properties of melt-spun AlSiMn anode materials for lithium-ion batteries

Electrochemical properties of melt-spun Al–Si–Mn alloy anodes for lithium-ion batteries

Melt-spun Al 70− X Si 30 Mn X ( X =0, 3, 5, 7, 10) Anode in Lithium-Ion Batteries

Influence of Annealing Treatment on Microstructure and Cycling Stability of La-Rich Ml(Nicomnal)(5) Alloy Electrode for Ni/Mh Batteries

The Effects of Partial Substitution of Mn by Cr on the Phase Structure, Microstructure and Electrochemical Properties of Ti-Zr-V-Mn-Ni Hydrogen Storage Alloys

The phase structure and electrochemical properties of the melt-spun alloy Zr0.7Ti0.3Mn0.4V0.4Ni1.2

Influence of the material processing on the electrochemical properties of cobalt-free Ml(NiMnAlFe)5 alloy

The Effects of Partial Substitution of Mn by Cr on the Electrochemical Cycle Life of Ti-Zr-V-Mn-Ni Alloy Electrodes of a Ni/MH Battery

Electrochemical Properties of the Ternary Alloy Li5alsi2 Synthesized by Reacting Lih, Al and Si As an Anodic Material for Lithium-Ion Batteries

Electrochemical Properties of SnSb-Mo Alloys Prepared by Mechanical Alloying for Li-ion Batteries

Performances of Al-xLi alloy anodes for Al-air batteries in alkaline electrolyte

Nanostructuring and Alloying of Si-Based Anode Materials

Microstructure and Electrochemical Performance of Thin Film Anodes for Lithium Ion Batteries in Immiscible Al–Sn System

Adding Metal Carbides to Suppress the Crystalline Li15Si4 Formation: A Route Toward Cycling Durable Si-Based Anodes for Lithium-Ion Batteries.

Effect of Rapid Solidification Process on the Alloy Structure and Electrode Performance of Zr(Ni0.55V0.1Mn0.3Cr0.55)2.1