Abstract:Microporous TiO 2 -SiO 2 composite membranes intended for use in the pervaporation dehydration of a water/isopropanol mixture were prepared via the sol–gel method using acetylacetone (ACA) as an organic chelating ligand (OCL). TiO 2 -SiO 2 -ACA sols were prepared by using titanium (IV) propoxide (TiTP), an alkoxide of Ti, tetraorthoethylsilicate (TEOS), an alkoxide of Si, and ACA, as a composite of TiO 2 and SiO 2 with coordinating OCL to Ti. The dried gels were fired at 300 °C under N 2 or at 500 °C under air, and were analyzed via FT-IR. Both powders had Ti-O-Si bonds, however, OCL in the powder fired at 500 °C in air has decomposed and removed. The TiO 2 -SiO 2 -ACA sols were applied to alumina plates and fired at either 300 °C under N 2 or at 500 °C under air to check the water-contact angle, which indicated that the OCL was retained on the plates fired at 300 °C under N 2 and were more hydrophobic than when fired at 500 °C under air. TiO 2 -SiO 2 -ACA composite membranes were fabricated by coating either the TiO 2 -SiO 2 -ACA sol layer fired at 300 °C under N 2 or that fired at 500 °C under air onto a TiO 2 -SiO 2 intermediate layer with an α-alumina support. The pore sizes of both membranes were estimated via the NKP method for single-gas permeance at 200 °C. The mean pore sizes of the membranes fired under N 2 at 300 °C and under air at 500 °C were 0.47 nm and 0.68 nm, respectively, which suggested the possibility of pore size control via firing conditions. Pervaporation tests of the TiO 2 -SiO 2 -ACA composite membranes in a water/isopropanol mixture (IPA: 90 wt%) showed that the membranes fired under air at 500 °C and under N 2 at 300 °C had values for permeation flux of 0.90 and 0.13 kg/(m 2 h) and separation factors of 667 and 98 at 50 °C, respectively. The higher permeation flux of the membrane fired under air at 500 °C was due to the influence of a larger pore size as well as to a more hydrophilic surface. On the other hand, the separation factor was also higher for the membrane fired under air at 500 °C, because the hydrophilic surface facilitated water permeation. These results indicate the possibility of using firing conditions to control both the pore size and the surface properties of microporous TiO 2 -SiO 2 -ACA composite membranes for use in PV separation.

Pervaporation of water/acetic acid through polyimide membranes from 3,3′, 4,4′-benzophenone tetracarboxylic dianhydride and 4,4′-oxydianiline

P(Vdf-Co-Hfp) Membrane for Recovery of Aroma Compounds from Aqueous Solutions by Pervaporation - I. Ethyl Acetate/Water System

Effect of the Permeants/Polymer Interactions on the Pervaporative Separation Properties of the P(Vdf-Co-Hfp) Membrane

Recovering Ethyl Acetate from Aqueous Solution Using P(VDF-co-HFP) Membrane Based Pervaporation

Pervaporation Properties of Polyimide Membranes for Separation of Ethanol + Water Mixtures

Pervaporation of water-acetic acid mixture through poly (4-vinylpyridine-co-acrylonitrile) membrane

Synthesis of novel membranes of polyimide with side-chains and their pervaporation performance

Experimental study on physical properties and pervaporation performances of polyimide membranes

PERVAPORATION SEPARATION FOR TOLUENE/n-HEPTANE MIXTURE BY POLYIMIDE MEMBRANES CONTAINING FLUORINE

Novel Thermally Cross-Linked Polyimide Membranes for Ethanol Dehydration Via Pervaporation

Separation of Dimethyl Carbonate/Methanol Mixtures by Pervaporation with Poly(Acrylic Acid)/Poly(Vinyl Alcohol) Blend Membranes

Pervaporation of Water/isopropanol Mixtures Through Polyaniline Membranes Doped with Poly(acrylic Acid)

Synthesis of Aromatic Polyimides Based on 3,4′-Oxydianiline by One-Pot Polycondensation in Molten Benzoic Acid and Their Application as Membrane Materials for Pervaporation

Block copolymer pervaporation membranes with microphase separated structures for ethyl acetate separation

Pervaporation Performance Ofpoly(acrylic Acid)-Poly(vinyl Alcohol) Blend Membrane for Separation of Methanol-Dimethyl Carbonate Azeotrope

I&Ec 104-Preparation And Pervaporation Performances Of Pea-Based Polyurethaneimide (Pui) Membranes To Benzene/Cyclohexane Mixture

Synthesis and Characterization of Soluble Polyimides Derived from 4,4′‐diamino‐3,3′‐dimethyldiphenylmethane and Their Pervaporation Performances

Poly(tetrafluoroethylene)/polyamide thin-film composite membranes via interfacial polymerization for pervaporation dehydration on an isopropanol aqueous solution

SYNTHESIS AND PERVAPORATION PERFORMANCE TO GASOLINE DEORGANICSULFIDE OF SOLUBLE POLYIMIDE

Surface-modified polyvinyl alcohol (PVA) membranes for pervaporation dehydration of epichlorohydrin (ECH), isopropanol (IPA), and water ternary feed mixtures

Pervaporation dehydration of an isopropanol aqueous solution using microporous TiO 2 -SiO 2 -OCL (Organic chelating Ligand) composite membranes prepared under different firing conditions