Abstract:Studying the dynamic aerodynamic characteristics and flow field characteristics for the dynamic mode transition in the variable cycle compression system (VCCS) can guarantee that the variable cycle engine (VCE) achieves high performance and stable mode transition. The common quasi-steady state analysis method cannot reflect the transient performance of the dynamic mode transition. Moreover, the dynamic simulation based on the dynamic grid technology will encounter the problem of negative volume grids because the adjustment range of variable components for VCCS is usually very large. To solve the problem, a dynamic simulation method based on real-time variation for geometry and aerodynamic boundaries of the dynamic mode transition in VCCS is first established in this paper. Using this method, the dynamic simulation was completed for the couple adjustment process of the outer bypass valve and variable stators of the dynamic mode transition in VCCS. The results of the dynamic simulation are compared with the quasi-steady state results. The results show that the rotor work ability and stator separation degree are affected by the stator variable angle degree and the mass flow rate (MFR) during the dynamic opening process of the outer bypass valve. For the MFR variation of 14.8%, when the stator variable angle is small (less than 3.3° in this study example), the flow separation on the variable stator blade pressure surface is increased during the dynamic opening process of the outer bypass valve. And the work ability of the downstream rotor is weakened. Therefore, in order to reduce the flow separation of stator blades with a small variable angle during the dynamic opening process of the outer bypass valve, a larger positive incidence angle can be adopted for stators at a small bypass ratio. For the whole dynamic process, the variation trend of the rotor work ability and stator separation state is opposite in the opening and closing process of the outer bypass valve. However, there is a dynamic effect of the flow field variation lagging behind the geometry variation in the opening and closing process. Therefore, the transient flow field in the opening and closing process is different from the quasi-steady state results, and the difference is more significant in the case of a small valve opening. Under a small valve opening, the work ability of the stage before the outer bypass entrance in the open process is significantly smaller than that in the closing process. And the difference in the flow field is mainly that the stator separation state of the stage before the outer bypass entrance in the open process is significantly weaker than that in the closing process. Therefore, the dynamic effect of the opening and closing process is more significant under a small valve opening, and the flow stability problem is more likely to occur during the dynamic mode transition in VCCS.

Modeling and Dynamic Analysis of the Mass Flow Control System Used for Rocket Engine

Modeling of a pneumatic system for high-accuracy position control

Dynamic characteristics of pilot-operated electro-hydraulic flow distribution system

Numerical Simulation of the Performance of the Sc-89 Jet Impact System

Thrust Hydraulic System of Casing Rotater with Flow Adaptive Control

Analysis and optimization of a hydraulic-feedback proportional throttlecartridge valve

Computational Study of Lateral Jet Interaction in Hypersonic Thermochemical Non-Equilibrium Flows Using Nonlinear Coupled Constitutive Relations

Research of Comprehensive Modeling of Two-Dimensional Vector Nozzle/Actuator Load/Turbofan Engine

CFD Simulation of Dynamic Characteristics of a Solenoid Valve for Exhaust Gas Turbocharger System

Throttling simulation and control of liquid oxygen/liquid methane rocket engine pressurized by the electric pump

Dynamics modeling and analysis of thrust-vectored V/STOL aircraft

Flow Force Analysis and Structural Optimization of a Large Flow Rate Pressure Compensation Valve

Modeling and Parameter Sensitivity Analysis of Valve-controlled Helical Hydraulic Rotary Actuator System

Modeling and dynamic characteristics analysis on solid attitude control motor using pintle thrusters

Dynamic Modelling Of A Small Scale Turbojet Engine

Parametric Analysis on Throttling Components of Multi-Stage High Pressure Reducing Valve

Dynamic Numerical Simulation Method and Flow Characteristic Analysis on the Mode Transition in Variable Cycle Compression System

Dynamic Characteristic Study of Staged Combustion Cycle Rocket Engine

Modeling and Dynamic Characteristics Analysis on a Three-Stage Fast-Response and Large-Flow Directional Valve

Performance Comparison of Control Strategies for a Variable-Thrust Solid-Propellant Rocket Motor

A method for numerical simulation of mode transition process of compression system of variable cycle engine based on throttle valve model