Abstract:Drying is a very important unit operation in many industries such as food, pharmaceuticals, chemicals and ceramics. In most cases, wet materials are dried by forced convection using hot air flow. Heat and mass transfer processes during drying have been studied by both experimental and numerical simulation methods. For the purpose of studying the mechanism of heat and mass transfer and stress-strain distribution during the hot air drying of biological porous medium, two-way coupled thermo-hydro-mechanical mathematical model has been developed to simulate the hot air convective drying process of biological porous media on basis of Fickian diffusion theory, Fourier’s law of heat conduction and thermoelasticity mechanics. The following assumptions were made in order to find a solution to the hot air drying model: the biological porous medium was homogeneous and isotropic; the deformation during drying was elastic. The transient model, composed of a system of partial differential equations, was solved by finite difference methods. The computational procedure was programmed using C language. Some physical and mechanical properties of carrot changing with dry basis moisture content and temperature were considered. The numerical results were compared with available experimental data obtained during the drying of potatoes and carrots. The relative errors between numerical results and experimental data were both less than 5%, which showed the numerical results obtained using the mathematical model were in good agreement with the experimental data. Numerical simulations of the drying curve variations and the spatio-temporal distributions of moisture, temperature and drying stresses and strains of carrot were also evaluated. The temperature and moisture content showed a gradient inside carrot slice during drying. As the drying process proceeded, the temperature inside the carrot slice initially increased to reach the wet bulb temperature of the environment and eventually leveled off. The dry basis moisture content inside the carrot slice decreased, with the fastest decreased at the heat and mass transfer interface, eventually reached the equilibrium moisture content of the potato and leveling off. Both the moisture content gradient and the temperature gradient decreased gradually in the thickness direction. The normal stress was negative in all parts of the carrot slice, and the larger the closer to the evaporation interface. The shear stress was positive in all parts of the carrot slice, and the maximum shear stress occurred in the middle of the carrot slice. As in the case of the normal stress, the values of the normal strain were negative. The change trend of normal strain with time was consistent with that of moisture content. These results indicated that the observed physical deformations were caused by the dehydration of carrot slice during drying. The influence of drying conditions, such as air temperature, air velocity and the thickness of porous media on drying process was analyzed. Analysis showed that under certain drying conditions, the higher air temperature, the greater air velocity and the thinner slice thickness, the shorter drying time. This work should help in developing an understanding of the relationship between mass and heat transfer, shrinkage, stress, strains and physical degradation.

Establishment for the Optimum Technological Conditions and the Optimized Process for Carrot Freeze-Drying

Effect of osmotic dehydration pretreatment of carrots

Mass Transfer During Osmotic Dehydration of Carrots

Study on Sublimation Drying of Carrot and Simulation by Using Cellular Automata

Vacuum Freeze-Drying of Soybean Phosphatidylcholine

Vacuum Drying Characteristics and Kinetics of Carrot Slices

Cryopreservation of Carrot (daucus Carota L.) Cell Suspensions and Protoplasts by Vitrification

Study on spray drying processing technology of carrot powder

Drying characteristics and drying quality of carrot using a two-stage microwave process

Mathematical Model and Numerical Simulation of Biological Porous Medium During Hot Air Drying

The freeze-drying performance under pressures from 1.325 to 101.325 kPa

Thermodynamic Analysis of a Freeze-Dryer Utilizing Hygroscopic Solution

Modeling of carrot thin layer convective drying process

Study on the response law between cooling rate and temperature with process parameters during vacuum freezing of liquid

Evaluating and Correlating the Mechanical, Nutritional, and Structural Properties of Carrots after Multiple Freezing/thawing Processing

Model of Mass and Heat Transfer during Vacuum Freeze-Drying for Cornea

Study on drying efficiency, uniformity, and physicochemical characteristics of carrot by tunnel microwave drying combined with explosion puffing drying

The simulation analysis and experiment of drying thin-layer radish strips

Effect of Freezing/Thawing Temperature on the Viscoelastic and Nutritional Qualities of Carrots

Investigation of Hot Air–Assisted Radio Frequency As a Final-Stage Drying of Pre-dried Carrot Cubes

Simplified computational model of the primary and secondary freeze-drying process of agriculture and marine foods