Abstract:Eutectic microstructures are one of the most common solidification patterns in the binary or multi-component alloy systems. Due to the fine periodic microstructures of the eutectic alloys, the commercial applications of the eutectic alloys can improve the mechanical properties of the castings. The solidification mechanism of eutectic alloys has been widely studied by a lot of experimental works and theoretical analysis over the years. Recently, numerical models were used to study the mechanisms of formation of phase patterns and selection dynamics of the lamellar eutectic, such as phase field (PF) and cellular automaton (CA) model, which can promote the development of eutectic growth theory. Based on the existing CA method for binary primary a phase, a modified cellular automaton (MCA) model was developed for the simulation of binary eutectic growth. In this model, the influence of constitutional and curvature undercooling on the interface morphology was considered. The growth rate of eutectic interface was calculated by the solute conservation at the alpha/liquid and beta/liquid interfaces. The model could simulate the phenomenon of overgrowth, splitting and steady state growth of the eutectic lamellar. CBr4-C2Cl6 eutectic transparent alloy was chosen to validate the model. The simulated results showed that the increasing pulling rate lead to a smaller eutectic lamellar spacing, which had a good agreement with the Jackson-Hunt theory and the experimental results from the literature. Eutectic morphology evolution was simulated under a constant pulling rate and temperature gradient, which showed that the stable lamellar structures existed when the initial lamellar spacing was in a finite range between the minimum stable spacing lambda(m) and the limiting maximum stable spacing lambda(M). A smaller initial lamellar spacing would lead to lamellar annihilation. Conversely, a larger initial lamellar spacing could lead to the lamellar nucleation due to the appearance of solute rich concave at the center of the alpha/liquid interface. Meanwhile, the oscillatory instability of the eutectic lamellar was also reappeared by the MCA model. The MCA model was easily extended to 3D, and the lamellar rod transition during directional solidification was simulated, which showed that the ratio of volume fraction of alpha and beta phase was smaller than 1/pi tend to form lamellar rod transition when the initial lamellar spacing was smaller than lambda(m).

Entropy As a Selection Rule for Crystal Growth in Undercooled Binary Eutectic Melts

Phase Field Simulation for Non-Isothermal Solidification of Multicomponent Alloys Coupled with Thermodynamics Database

Non-equilibrium solidification of bulk undercooled Ni–P eutectic alloys

Modeling of Regular Eutectic Growth of Binary Alloy Based on Cellular Automaton Method

Phase Selection During Solidification of Undercooled Ni 70.2 Si 29.8 Eutectic Alloy

Comparative Analysis of Isothermal and Non-Isothermal Solidification of Binary Alloys Using Phase-Field Model

Phase Stabilities of High Entropy Alloys

Simulation of Eutectic Growth in Directional Solidification by Cellular Automaton Method

Experimental Study and Numerical Simulation of Microstructure Evolution in Al-Si Eutectic Solidification Process

Modeling the Overall Solidification Kinetics for Undercooled Single-Phase Solid-Solution Alloys. II. Model Application

Eutectic growth in bulk undercooled melts

Phase stability in high entropy alloys: Formation of solid-solution phase or amorphous phase

Phase-field Simulation of Dendritic Growth for Binary Alloys with Complicate Solution Models

A numerical study of irregular eutectic in Al-Si alloys under a large undercooling

A New Coupled Model for Alloy Solidification

Modeling of Eutectic Spacing in Binary Alloy under High Pressure Solidification

Modelling Of The Thermosolutal Convection And Macrosegregation In The Solidification Of An Fe-C Binary Alloy

Basic Thermodynamic Research Of Eutectic High Entropy Alloys Formation

Phase selection rule of high-entropy metallic glasses with different short-to-medium-range orders

A phase-field approach for modeling equilibrium solute segregation at the interphase boundary in binary alloys

Solute Segregation And Thermal Stability Of Nanocrystalline Solid Solution Systems