Abstract:Thermal analysis and microstructure characterization provide information regarding material thermal profiles and microstructure formation. Wrought aluminium alloys offer significant advantages in terms of higher ultimate tensile strength (UTS) and yield strength but relatively poor fluidity properties. The objective of this experiment presented in this paper was to understand the relationship between solidification rate, metallurgical behaviour, and fraction phase growth of wrought aluminium 6061. This information was crucial and important to the foundry industry to understand the material behaviour that will help to cast wrought aluminium 6061. Thermal analysis and microstructure of wrought aluminium 6061 on different cooling conditions are present in this paper. In this work, Aluminium 6061 heated and melted in a graphite crucible at a temperature of 800°C. Two thermocouples located at the centre and 20 mm from the graphite crucible wall. Slow cooling rate condition experiment rig was developed by placing graphite crucible into a chamber with kaowool insulation. Normal cooling rate condition was developed by allowing the molten solidify at room temperature. Fast cooling rate condition was prepared by applying a forced airflow over the graphite crucible. The slow, normal, and high cooling rates were calculated at 0.03°C/s, 0.2°C/s and 0.3°C/s respectively. Cooling curve analysis was performed to predict various areas of solidification phase and fraction solid. In Addition, the microstructure formation was observed, recorded, and compared between different cooling conditions. The results show slow cooling rate condition formation of eutectic and solidus temperatures occurred far from liquidus temperature. The eutectic and solidus temperature was increased with the increment of the cooling rate. Furthermore, the DCP temperature of slow cooling rate condition at 638.3°C was the lowest while gives wider temperature range corresponding to the fraction solid percentage increment. Meanwhile, an increase in cooling rate refined the microstructure, improved the grain circularity and at the same time reduced the aspect ratio.

Effect of Microstructure on Thermal Expansion Coefficient of 7A09 Aluminum Alloy

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

Effects of Y content on microstructures and thermal expansion behavior of Mg-Al-Y alloys

Effect of Solution Heat Treatment on the Microstructure and Microhardness of 7050 Aluminum Alloy

Study of the Thermal Physical Properties of Ti47Ni44Nb9 Wide Hysteresis Shape Memory Alloy

Tuning Thermal Expansion by a Continuing Atomic Rearrangement Mechanism in a Multifunctional Titanium Alloy

Influence of thermal exposure on the microstructure evolution and mechanical behaviors of an Al-Cu-Li alloy

Microstructure evolution of a forged TiAl-Nb alloy during high-temperature tensile testing

Effect of Annealing Temperature on As-Cast Ti6Al4V–5Cu Alloy Microstructure, Tensile Properties, and Fracture Toughness

Dislocation density model and microstructure of 7A85 aluminum alloy during thermal deformation

Grain-resolved temperature-dependent anisotropy in hexagonal Ti-7Al revealed by synchrotron X-ray diffraction

Effect of Thermal Exposure on the Microstructure and Mechanical Properties of 2A97 Al-Li Alloy

THERMAL STABILITY AND THERMAL EXPANSION BEHAVIOR OF AlFeCoNiCu AS-CAST HIGH-ENTROPY DUAL-PHASE ALLOY

Effects of grain size on the precipitation pathway and mechanical properties of (CoCrFeNi)94Ti2Al4 high entropy alloy

Effect of extrusion process on the stress corrosion cracking resistance of 7N01 aluminum alloy

Microstructural Modelling Solution for Complex Co Based Alloys and Coatings

The influences of temperature and microstructure on the tensile properties of a CoCrFeMnNi high-entropy alloy

Effect of three-dimensional deformation at different temperatures on microstructure, strength, fracture toughness and corrosion resistance of 7A85 aluminum alloy

Experimental and theoretical study of the microstructure evolution and thermal-physical properties of hypereutectic Al–Fe alloys

Effect of temperature on mechanical behavior of Cu–Cr–Co–Ti alloys

Effect of Different Cooling Rates Condition on Thermal Profile and Microstructure of Aluminium 6061