Abstract:Injection molding is widely used for the mass production of plastic components. However, an appropriate choice of the process parameters is essential to ensure the precision and uniformity of the molded parts. The flow length-to-wall thickness (L/t) ratio for most molded components lies in the range of 100∼200. For higher values of the L/t ratio, the flow resistance increases dramatically at the end of the molded part and the injection pressure propagates less easily through the mold cavity. Consequently, the geometric dimensions of the molded parts in the near-gate region are frequently different from those in the far-from-gate region as well as resulting in lower uniformity. In practice, the variation in the geometric dimensions is significantly dependent on the filling-to-holding (V/P) switchover point, injection speed, and holding condition. Accordingly, the present study commences by proposing a simple least-squares regression-based approach for determining the appropriate V/P switchover point based on the quality requirement for the geometric dimensions of the molded component. In addition, a multi-stage holding condition is used to improve the geometric uniformity of the molded component by minimizing the residual pressure difference between the near-gate and far-from-gate regions of the mold at the end of the packing stage. Finally, a deceleration strategy is considered for the injection screw at the end of the filling stage to further reduce the quality variation. The experimental results show that for molded components with a large L/t ratio, the V/P switchover point should be determined based on the quality requirement for the part in the far-from-gate region in order to avoid insufficient quality compensation in the early holding stage. Furthermore, compared with the single-stage holding condition, the multi-stage holding condition reduces the residual pressure difference between the near-gate and far-from-gate regions of the cavity by around 74.5% (from 48.7 to 12.5 MPa). As a result, the difference in width between the near-gate region of the molded component and the far-from-gate region is reduced by about 66.7% (0.09 to 0.03 mm), while the difference in thickness is reduced by approximately 32.1% (0.028 to 0.019 mm). The deceleration strategy for the injection screw has no noticeable effect on the quality uniformity of the molded part provided that the V/P switchover point and multi-stage holding pressure are appropriately designed.

Injection-Compression Molded Part Shrinkage Uniformity Comparison Between Semicrystalline and Amorphous Plastics

Effects of Injection Molding Process Parameters on the Chemical Foaming Behavior of Polypropylene and Polystyrene

Influence of gas counter pressure injection molding parameters on shrinkage ratio of plastic part

The influence of mold design and process parameters on dimensional shrinkage of perfluoroalkoxy alkane injection molding parts

An Investigation to Reduce the Effect of Moisture on Injection-Molded Parts through Optimization of Plasticization Parameters

Influence of process parameters and post-molding condition on shrinkage and warpage of injection-molded plastic parts with complex geometry

Effect of processing parameter changes on mechanical properties during injection molding: Amorphous versus semi‐crystalline materials

Crystallinity and mechanical properties of polypropylene products foamed by microcellular injection molding process

Research on the Effects of Process Parameters on Shrinkage Variation of the Rapid Heat Cycle Molding Plastic Part

Effect of rapid heating cycle injection mold temperature on crystal structures, morphology of polypropylene and surface quality of plastic parts

Effect of Gas Counter Pressure on the Surface Roughness, Morphology, and Tensile Strength between Microcellular and Conventional Injection-Molded PP Parts

Influence of V/P switchover point, injection speed, and holding pressure on quality consistency of injection‐molded parts

Effects of Injection Molding Parameters on Properties of Insert-Injection Molded Polypropylene Single-Polymer Composites

Reducing part deformation of isotactic polypropylene specimens fabricated with powder bed fusion technique through controlling crystallization behaviors

A study of packing profile on injection molded part quality

Comparative study of chemical and physical foaming methods for injection-molded thermoplastic polyurethane

Study on the influence of in-mold sequential injection molding process parameters on mechanical properties of self-reinforced single composites

Determination of process parameters based on cavity pressure characteristics to enhance quality uniformity in injection molding

Effect of Compatibility on the Foaming Behavior of Injection Molded Polypropylene and Polycarbonate Blend Parts

Investigation of adhesion phenomena in thermoplastic polyurethane injection molding process

Formation and Distribution of the Mesophase in Ultrasonic Micro-Injection-Molded Isotactic Polypropylene