Abstract:Injection molding is widely used for the mass production of plastic components. However, an appropriate choice of the process parameters is essential to ensure the precision and uniformity of the molded parts. The flow length-to-wall thickness (L/t) ratio for most molded components lies in the range of 100∼200. For higher values of the L/t ratio, the flow resistance increases dramatically at the end of the molded part and the injection pressure propagates less easily through the mold cavity. Consequently, the geometric dimensions of the molded parts in the near-gate region are frequently different from those in the far-from-gate region as well as resulting in lower uniformity. In practice, the variation in the geometric dimensions is significantly dependent on the filling-to-holding (V/P) switchover point, injection speed, and holding condition. Accordingly, the present study commences by proposing a simple least-squares regression-based approach for determining the appropriate V/P switchover point based on the quality requirement for the geometric dimensions of the molded component. In addition, a multi-stage holding condition is used to improve the geometric uniformity of the molded component by minimizing the residual pressure difference between the near-gate and far-from-gate regions of the mold at the end of the packing stage. Finally, a deceleration strategy is considered for the injection screw at the end of the filling stage to further reduce the quality variation. The experimental results show that for molded components with a large L/t ratio, the V/P switchover point should be determined based on the quality requirement for the part in the far-from-gate region in order to avoid insufficient quality compensation in the early holding stage. Furthermore, compared with the single-stage holding condition, the multi-stage holding condition reduces the residual pressure difference between the near-gate and far-from-gate regions of the cavity by around 74.5% (from 48.7 to 12.5 MPa). As a result, the difference in width between the near-gate region of the molded component and the far-from-gate region is reduced by about 66.7% (0.09 to 0.03 mm), while the difference in thickness is reduced by approximately 32.1% (0.028 to 0.019 mm). The deceleration strategy for the injection screw has no noticeable effect on the quality uniformity of the molded part provided that the V/P switchover point and multi-stage holding pressure are appropriately designed.

The influence of mold design and process parameters on dimensional shrinkage of perfluoroalkoxy alkane injection molding parts

Shrinkage and Warpage Mechanism of Overflow Water-Assisted Injection Molding Short Fiber-Reinforced Polymers

Influence of gas counter pressure injection molding parameters on shrinkage ratio of plastic part

Influence of process parameters and post-molding condition on shrinkage and warpage of injection-molded plastic parts with complex geometry

Research on metallic contamination control of PFA injection molded fittings

Effects of Process Parameters on Shrinkage Uniformity and Birefringence of Injection-Compression Molded Parts

Analysis of the Warpage Phenomenon of Micro-Sized Parts with Precision Injection Molding by Experiment, Numerical Simulation, and Grey Theory

Effect of Dynamic Injection Molding Process Parameters on Shrinkage of Parts

A Study on the Distinguishing Responses of Shrinkage and Warpage to Processing Conditions in Injection Molding

Simulation and Optimization of Injection Molding for Precise Drip Emitters

Effects of processing parameters on shrinkage uniformity of injection-compression molded part

Influence of V/P switchover point, injection speed, and holding pressure on quality consistency of injection‐molded parts

Influence of mold design and injection parameters on warpage deformation of thin-walled plastic parts

Effect of processing parameter changes on mechanical properties during injection molding: Amorphous versus semi‐crystalline materials

Research on the Effects of Process Parameters on Shrinkage Variation of the Rapid Heat Cycle Molding Plastic Part

Determination of process parameters based on cavity pressure characteristics to enhance quality uniformity in injection molding

Influence of Processing Conditions on the Morphological Structure and Ductility of Water-Foamed Injection Molded PP/LDPE Blended Parts

Enhancing the quality stability of injection molded parts by adjusting V/P switchover point and holding pressure

Numerical Optimization of Shrinkage and Warpage on the Injection Molding Process Parameters of Electrical Connector

Research on Optimization of Injection Molding Process Parameters of Automobile Plastic Front-End Frame

Design and Parametric Optimization of the Injection Molding Process Using Statistical Analysis and Numerical Simulation