Abstract:Multi-stage microforming is increasingly used in manufacturing of the miniaturized parts with complex structures and geometries. Optimization design of this type of manufacturing process, however, is still challenging due to its unknown intrinsic nature of the process. In the multi-stage deformation and microforming, the size effect (SE), the strain path change (SPC), and the intragranularly misoriented grain boundary (IMGB) generated in previous forming stage, are the main factors governing the deformation behaviors of ultra-thin sheets. To gain thorough insights into their influences on deformation and elucidate the associated micro-scaled mechanisms, SS 316L ultra-thin sheets with the thickness of 0.1 mm and different mean grain sizes (d) were used for two-stage tensile tests under the conditions with distinct pre-strain & epsilon;pre and intersection angle & theta;SPC (the angle between the previous loading direction and subsequent one). Mechanical tests reveal that increasing & epsilon;pre and & theta;SPC reduces the yield stress and hardening rate in SPC tension, but this reduction gets smaller after increasing d. This is because more IMGBs with complex pattern are formed in relatively large grains, raising the permanent deformation resistance inside grains in subsequent tension. To model the IMGB-induced hardening, the SPC-induced softening, and the SE-induced concurrent facilitations to the hardening and softening, an enhanced crystal plasticity constitutive relation was established. The physical essence that IMGB obstructs dislocation movement, is used to model the IMGB-induced hardening based on the interactions between the main slip planes and IMGBs. The hardening facilitation caused by increasing grain size is implicitly incorporated in determining the saturated slip resistance. Modelling of the SPC-induced softening is based on the high Schmid factor grain fraction and its influences are governed by pre -strain and the defined SPC parameter. The softening facilitation caused by coarsening grains is modelled in establishing the initial slip resistance in SPC deformation. The proposed simulation procedure and constitutive relationship help with accurately predicting the mechanical response and microstructure evolution in micro-scaled SPC deformation, and also provide a basis for modelling and design of the multi-stage microforming of complex miniaturized parts.

Construction of a Composite Model of Decreasing Flow Stress Scale Effect

Discussion and Prediction on Decreasing Flow Stress Scale Effect

The Numerical Simulation of Decreasing Flow Stress Scale Effect

Simulation and Discussion on the Decreasing Flow Stress Scale Effect

Simulation Study on Fluctuant Flow Stress Scale Effect

Achieving High Strength and High Ductility in Nanostructured Metals: Experiment and Modelling

The Scale Effect of Flow Stress Fluctuation in Micro Scale

Modeling of Flow Stress Size Effect Based on Variation of Dislocation Substructure in Micro-Tension of Pure Nickel

A constitutive model on flow stress prediction from the contribution of twin and grain refinement, strain and strain rate during surface mechanical attrition treatment of metals

A Constitutive Model for Metal Plastic Deformation at Micro/meso Scale with Consideration of Grain Orientation and Its Evolution

New Constitutive Model for the Size Effect on Flow Stress Based on the Energy Conservation Law

Plastic Deformation Size Effects in Micro-Compression of Pure Nickel with A Few Grains Across Diameter

Crystal Plasticity-Based Analysis and Modelling of Grain Size and Strain Path Dependent Micro-Scaled Deformation Mechanisms of Ultra-Thin Sheet Metals

Effects of Specimen Size on Flow Stress of Micro Rod Specimen

Modeling and Analysis of Size Effects on Pure Copper Mechanical Behaviors in Micro Scale Plastic Deformation Processes

Seventy years of Hall-Petch, ninety years of superplasticity and a generalized approach to the effect of grain size on flow stress

Constitutive Model for Thin Sheet Metal with One or Several Grains Across Thickness in Micro-Forming

A microscale constitutive model for thin stainless steel sheets considering size effect

Size Effect on Flow Stress in Uniaxial Compression of Pure Nickel Cylinders with A Few Grains Across Thickness

The Modified GTN-Thomason Criterion for Modelling of Ductile Fracture Considering Shear Factor and Size Effect in Micro-Scaled Plastic Deformation

Co-effect of Microstructure and Surface Constraints on Plastic Deformation in Micro- and Mesoscaled Forming Process