Abstract:Equal channel angular pressing (ECAP) is an efficient metal forming tool, generally used to improve the mechanical properties by refining the grain structure in metals and alloys. In the present work, both experimental and simulation approaches have been utilized to investigate the deformation behavior of EN AW 7075 alloy during ECAP. The formation and homogeneity of the Von-Mises stress and plastic strain of the samples during ECAP with different outer corner angles (OCAs) have been investigated by the finite element method (FEM). The results revealed that the effective strain was higher and uniform for 10°, 20°, and 30° OCAs die compared to other OCAs. Beyond 30°, the magnitude of strain was found lower with a less homogenous distribution of strain. A sharp plastic deformation zone (PDZ) was noticed for 10° and 20° OCAs, although broadened gradually over an OCA value of 20°. Moreover, lower and uniform Von-Mises stress was generated along the diameter of the sample for the OCA of 20° compared to other OCAs. A gradual reduction of plastic strain has been documented with the enhancement of OCAs along with the sample diameter. The sharpest damage, however, was noticed for the OCA of 90° due to the higher gap between the sample and both die surfaces. Interestingly, the most uniform severe plastic deformation and highest strain homogeneity in terms of inhomogeneity index and coefficient of variance were achieved for 20° and 30° OCAs. Electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) analysis illustrated the formation of ultra-fine grain structures containing very fine η ́ and η precipitates during the post-ECAP process. An improvement in the hardness, yield strength, and ultimate strength by 22%, 18%, and 14%, respectively, after ECAP has been recorded in comparison to the initial artificially aged condition. The improvements in mechanical properties were improvised primarily due to grain refinement combined with precipitate hardening.

Modeling and Experimental Observation of the Plastic Anisotropy and Damage of CP-Ti during Multi-Pass ECAE

Tensile and Compressive Deformation Behaviors of Commercially Pure Al Processed by Equal-Channel Angular Pressing with Different Dies

Tensile Deformation Behaviors of CuNi Alloy Processed by Equal Channel Angular Pressing

Study on the Effect of Tool Inclination Angle in Machining Process Based on Three-Dimensional Thermo-Elastic-Plastic Model

3D FEM Simulation of Multipass ECAP Ti-50.8%Ni at Various Temperatures

The Role of Material Model in the Finite Element Simulation of High-Speed Machining of Ti6Al4V

Electrical-thermal-mechanical coupled modeling and simulation on deformation behaviors of Ti6554 alloy in electrically-assisted micro-tension

Application of Smeared Cracking and Damaged Plasticity Models in FEA of CFT

Mechanical response and texture evolution prediction of AZ31 magnesium alloy during CVCDE process using crystal plasticity finite element method

Unusual plastic deformation and damage features in Titanium: experimental tests and constitutive modeling

Simulation prediction of CP-Ti slab ingot solidification structure based on the CAFE method

Development of mechanical properties and microstructure for Al–Zn–Mg–Cu alloys through ECAP after optimizing the outer corner angles through FE modeling

Experimental study and Finite Element Modelling of Pure Copper Tube Fabrication via the Parallel Tubular Channel Angular Pressing (PTCAP) Process

A multiscale elastoplastic tensive behavior of quasi-continuous network structured (Ti 3 AlC 2 -Al3Ti)/2024Al composite

Hierarchical Deformation and Anisotropic Behavior of (α+β) Ti Alloys: A Microstructure-Informed Multiscale Constitutive Model Study

Characterization of microstructural evolution and mechanical properties of Cu-Ni-Cr alloys deformed by ECAP

Effects of Ecae Process on Microstructure and Transformation Behavior of Tini Shape Memory Alloy

A thermal activation based constitutive model for the dynamic deformation of AA5083 processed by large-scale equal-channel angular pressing

Experimental and Crystal Plasticity Finite Element Investigations of Plastic Anisotropy in Additively Manufactured Ti6Al4V Alloy

Calibration and application of damage and rate-dependent constitutive model for SPCE steel

Experimental and crystal plasticity modelling study on the crack initiation in micro-texture regions of Ti-6Al-4V during high cycle fatigue tests