Abstract:Using cobaloxime boron fluoride (COBF) and AIBN as catalyst and initiator respectively, the catalytic chain transfer bulk polymerization of 2-hydroxyporpyl methacrylate ( HPMA) was carried out at 60 degrees C and the low molecular weight polymer with a terminal double bond was prepared. The evolution of the apparent chain transfer constant (C-S(spp)) of COBF during the polymerization was determined by the Mayo equation and the CLD (chain length distribution) equation respectively. At the beginning of the reaction the chain transfer constant showed values of up to about 2000, but with the increasing of the monomer conversion, the chain transfer constant decreases and keeps at a value of about 600 for sometime and then decreased again. The most likely cause for the catalyst deactivation is the stable cobalt-carbon bond formed at the first period of the reaction and then reached equilibrium point. When the polymerization proceeds up to middle and high conversion, the chain transfer polymerization is further manipulated by diffusions of polymeric propagating chain and catalyst molecules, and the apparent chain transfer constant fell to value of below 300. It has been found also, that the data determined by the CLD equation are usually lower than those by the Mayo equation, especially at high conversion stage. It is because that both original equations are available for the instantaneous produced polymer or the case of very lower conversion stage. However, the GPC measurements give molecular weight distributions of the cumulated products rather than the instantaneous produced polymer. The number-average polymerization degrees for the instantaneous produced polymers were obtained from the GPC data, and used in the Mayo equation method together with the modification of the monomer concentration. It was believed that the apparent chain transfer constants from the modified Mayo equation method are more available for the middle and high conversion cases.

Influence of Termination and Transfer on Molecular Weight Distribution of Polymer—10. Chain Transfer to Monomer and Impurity

Influence of Termination and Transfer on Molecular-Weight Distribution of Polymers .5. Chain Transfer to Monomer and Impurity Termination

Influence of Termination and Transfer on Molecular-Weight Distribution of Polymers .7. Impurity Transfer

Influence of Termination and Transfer on Molecular-Weight Distribution of Polymers .9. Chain Transfer to Monomer and Spontaneous Transfer

Influence of Termination and Transfer on Molecular Weight Distribution of Polymers. IV. Impurity Termination

Influence of Termination and Transfer on Molecular Weight Distribution of Polymers, 6. Chain Transfer to Monomer and Spontaneous Termination

Influence of Termination and Transfer on Molecular-Weight Distribution of Polymers .8. Spontaneous Transfer

Influence of Termination and Transfer on Molecular Weight Distribution of Polymers, 2. Radical‐radical Termination and Monomer Chain Transfer

Influence of Termination and Transfer on Molecular Weight Distribution of Polymers. I. Disproportionation and Combination

Modeling and Experimentation of RAFT Solution Copolymerization of Styrene and Butyl Acrylate, Effect of Chain Transfer Reactions on Polymer Molecular Weight Distribution

Modeling for the Diffusion Limitation of Free Radical Polymerization

INFLUENCE OF MONOMER COMPOSITION ON THE CHAIN TRANSFER COEFFICIENT IN METHYL METHACRYLATE/BUTYL ACRYLATE RAFT COPOLYMERIZATION

THE EVOLUTION OF THE CHAIN TRANSFER CONSTANT DURING THE CATALYTIC CHAIN TRANSFER POLYMERIZATION OF 2-HYDROXYPROPYL METHACRYLATE

Graphical Method for Polymerization Kinetics. II. Influence of Monomer Transfer on Molecular Weight Distribution for Anionic Polymerization Initiated by Multifunctional Initiator

Equilibrium Polymerization with Reversible Termination

Kinetic Analysis Of ''Living'' Polymerization Processes Exhibiting Slow Equilibria .5. Effect Of Monomer Transfer In Cationic Polymerization And Similar Living Processes

Kinetic Model for Lonic Polymerization Initiated by Difunctional Initiator with Monomer Transfer

The Influence of the Penultimate Chain Element on Monomer Transfer in Living Polymerization

Modeling Analysis of Chain Transfer in Reversible Addition‐fragmentation Chain Transfer Polymerization

Kinetic Model for a Polymerization Process Where the Rate Constants of Both Propagation and Termination by Monomer Depend on Chain‐length

Kinetic Model of Pulsed Laser-Initiated Polymerization in the Presence of Chain Transfer to Monomer