Abstract:Microcracks are easily generated inside polymers and polymer composites during their service in structural applications. Development and coalescence of microcracks would bring about catastrophic failure of the materials and then reduce their lifetimes. Therefore, early sensing, diagnosis and repair of microcracks become necessary for removing the latent perils. In this context, the materials possessing self-healing function are ideal for long-term operation. Attempts have been made to develop solutions in this filed, among which the route based on microcapsulation seems to be promising. Self-repairing polymer composites containing microencapsulated healing agent have attracted more and more research interests. The present article analyzed the existing problems and proposed the criteria for manufacturing qualified microencapsulated healing agent. Accordingly, microcapsules containing epoxy resin were successfully fabricated by in situ polymerization in an oil-in-water emulsion with poly(melamine-formaldehyde) (PMF) as the shell material and high-activity low-viscosity diglycidyl tetrahydro-o-phthalate (DTP) as the core substance. The typical synthesis procedures are described below. About 50 g DTP was added into 250 mL aqueous solution of 2 % styrene-maleic sodium (SMS). The mixture was vigorously agitated by a homogenizer for 10 min at a selected rate and then two drops of I-octanol were added to eliminate surface bubbles of the emulsion. The pre-condensate of 12.5 g melamine and 27.1 g formaldehyde was prepared at 70 similar to 75 degrees C for 30 min, and the pH value of the solution was kept at about 9 similar to 10 by adding triethanolamine. Subsequently, the precondensate solution was added to the above emulsion with 450 r/min continuous mechanical stirring by a two-bladed stirring paddle while the pH value of the solution was adjusted by adding citric acid. Eventually, the reaction mixture was cooled down to room temperature. The resultant slurry was neutralized by 2 % sodium carbonate solution, and then diluted with deionized water. The deposit of microcapsules was separated through a Buchner funnel and rinsed with deionized water and then vacuum dried. The synthesis method was improved by optimizing the processing parameters. The appropriate reaction time was about 30 similar to 60 min. Further extension of time had little influence on the products. The reaction temperature should be set at about 50 similar to 70 degrees C. The pH value of about 3.2 was appropriate and had complex effect on the properties of the products. The appropriate core/shell mass ratio was about 2:1 similar to 3:1. The size and size distribution of microcapsules were mainly determined by the dispersion rate and the emulsifier content. Having been encapsulated, the core material DTP kept the same activity as its raw version. The microcapsules' shell wall was relatively thin (ca. 0. 2 mu m), which assured sufficient core content (83.2 wt %) even if the microcapsules were very small (ca. 6.7 mu m). Moreover, the microcapsules were proved to be strong enough to survive handling during manufacturing self-healing composites. Having been pre-embedded in cured epoxy, the microcapsules had satisfied affinity to the matrix. They can be readily ruptured releasing DTP fluid as expected upon damaging of the composite, and activity of the released core material was the same as the raw material. Besides, the microcapsules had good sealing ability and high stability. They can be stored at room temperature for long time and could bear moderate or high temperatures applied for curing composites.The resent work provided a new simple approach for mass-production of epoxy loaded microcapsules, which can be used to manufacture self-healing composites or other self-curing stuffs like single constituent epoxy adhesive and self-locking threaded fasteners.

STUDY ON THE PREPARATION TECHNICS OF EPOXY RESINS COATED POLYSTYREN SELF-REPAIR MICROCAPSULES

Study On Preparation and Mechanism of Self-healing Poly(urea-formaldehyde) Microcapsules

Optimal Preparation and Characterization of Poly(urea–formaldehyde) Microcapsules

Preparation And Application Of Melamine-Urea-Formaldehyde Self-Healing Microcapsules Modified By Nano-Al2o3

Study on the curing kinetics of epoxy resin in self-healing microcapsules with different shell material

Preparation and Self-Repairing Properties of Urea Formaldehyde-Coated Epoxy Resin Microcapsules

Development of PS Coated Epoxy Resin Microcapsule

PREPARATION OF EPOXY RESIN MICROCAPSULES BY IN SITU POLYMERIZATION

The Preparation and Research of Microcapsules in Self-Healing Coatings

Preparation and Characterization of Poly (Melamine-Formaldehyde) Walled Microcapsules Containing Epoxy

Preparation and characterization of self‐healing microcapsules with poly(urea‐formaldehyde) grafted epoxy functional group shell

The Preparation of Microcapsules Used for Self-Healing Composites

Styrene and BPO Poly (Urea-Melamine-formaldehyde) Microcapsules Prepared Via in Situ Polymerization to Promote the Self-Healing Properties of Epoxy Composites

Effects of Processing Conditions on the Properties of Epoxy Resin Microcapsule

Preparation of poly（urea melamine and formaldehyde composite resin） walled microcapsules containing styrene

Preparation and research of epoxy resin microcapsules

Preparation And Characterization Of Microencapsulated Polythiol

Preparation and Properties Research of Self-healing Microcapsules of Reactive Ethylene Silicone Oil/poly(urea-formaldehyde)

Preparation and Mechanical Properties of Microcapsule Made of Self-Repairing Composite Materials

Preparation and Characterization of Poly(urea-Formaldehyde) Microcapsules Filled with Epoxy Resins

Epoxy resin nano microcapsule and preparation method thereof