Design and Realization of Virtual Logic Analyzer Based on USB2.0 Bus

唐海洋,翟巍,王勇

2007-01-01

Abstract:This paper introduces the design and realization of a high-speed and low-cost virtual logic analyzer based on FPGA and USB2.0 bus. Mainlyexpatiates on the trigger modes design of the logic analyzer and the way to create USB interface by CP2102 chip that can realize the communicationbetween PC and the system.

What problem does this paper attempt to address?

Design and Implementation of the High-Performance Link Layer in High-Speed Serial Communication

Yong-jian TANG,Le-nian HE,Xiao-lang YAN

DOI: https://doi.org/10.3969/j.issn.1000-7180.2005.04.037

2005-01-01

Abstract:The USB2.0 supports the high-speed signaling at 480 Mbps. It can meet the needs of image and voice signal transmitting. In this paper, after demonstration of the characters and functions of high speed digital circuit of USB2.0 link layer, a novel design and implementation method of data recovery circuits, which is based on all digital phase-looked loop (ADPLL), for the full-speed mode, as well as a new approach of parallel implementation of the encode/decode module in high-speed mode were proposed. The simulation results indicated that the circuit has reached 480MHz. A FPGA hardware simulation system was developed, in which the functions of link layer was verified.
Design of Data Communication Interface of Data Acquirement System Based on USB

陈章位,赵玉刚

DOI: https://doi.org/10.3321/j.issn:1004-132X.2004.20.014

2004-01-01

Abstract:An interface based on USB is designed for Data Acquirement System with DSP chips. Cypress EZ-USB technology and FPGA technology were used in this interface. This kind of interface can achieve high speed data communication between the Data Acquirement System and the PC in the USB 1.1 protocol, and it can meet the requirements of high speed and real-time requirements.
Design of USB2.0 Protocol Analyzer Based on FPGA

Hu Wei,Zhang Xinjia,Li Meifeng,Zhang Degang,Liu Hang

DOI: https://doi.org/10.16526/j.cnki.11-4762/tp.2008.09.047

2008-01-01

Abstract:The transparency of Universal Serial Bus transactions has brought various inconveniences in developing and testing of USB systems;the equipments currently used for USB physical layer test and analysis usually have high cost and serious acquisition dead-time problems.A USB 2.0 protocol analyzer based on FPGA is designed,which carried out real-time sampling of both high-speed and full-speed USB device differential data buses,overcame the acquisition dead-time problem through the concurrent processing feature of hardware,solved data accumulation and packet loss problems caused by the phase difference of independent USB interfaces,reduced performance requirements towards the main processor,decreased design cost and provided effective support for developing and testing of USB systems.
Design of high speed data sampling system based on FPGA and USB2.0

Wu Zhenyu,Chang Yubao,Feng Lin

DOI: https://doi.org/10.3321/j.issn:0254-3087.2006.z1.049

2006-01-01

Abstract:The paper introduces the using of FPGA and USB in the design of VI system based on data acquisition system.In the system,we use FPGA as control core.USB2.0 is used for interface to realize the fast data transmission between the FPGA and the PC.Through the combination of soft and hardware,a multichannel analogy signal and digital logic signal acquisition system are implemented.In addition,firware and USB device drive are also introduced.
USB Visual Oscilloscope Based on FPGA

FENG Lin,LI Li,WU Zhen-yu,JIN Bo,WANG Shan-kun

DOI: https://doi.org/10.3969/j.issn.1002-1841.2011.07.021

2011-01-01

Abstract:This paper introduced USB visual oscilloscope system based on FPGA and AD9224.It realized analog-digital converter through AD9224.It implemented logic control of multipluxer,variable gain amplifier,A/D and D/A,and internal FIFO high-speed buffer memory through FPGA.It made full use of FPGA control functions to achieve auto shift control through D/A converter.The data transmission between data acquisition board and PC was realized by CY7C68013A chip,and controlled by FPGA directly.The human-computer interaction software was programed by LabVIEW to show wave and other data result on upper monitor.This visual oscilloscope implements data acquisition,storage,transmission,display and multifunction digital signal processing.Measureing experiments show the system is stable and can meet application requirements of portability.
Design and Realization of Low Cost USB Protocol Converter

杨章顺,冉立新

DOI: https://doi.org/10.3969/j.issn.1000-3428.2004.18.069

2004-01-01

Abstract:USB has become popular due to its high speed, plug and play feature and the capability to avoid resource conflict. An embedded converter from other low speed bus to USB is very interesting, since it would allow legacy peripheral devices to experience USB advantages without major changes. The paper presents a universal USB1.1 protocol converting scheme, and an example of PS/2-USB converter is also given.
Designs of USB2.0 interface of data acquisition card

Qiao Liyan,Wu Jiangwei,Xu Hongwei

DOI: https://doi.org/10.3969/j.issn.1002-7300.2010.01.017

2010-01-01

Abstract:Data acquisition has been widely used in industrial production.Based on summarization of the hardware architecture,the thesis gives a detailed description of the design of USB interface,including the hardware design of USB2.0,The interface logic design in FPGA,USB firmware design,USB driver program design,and the application design.Through the experimental test,the result proves the design meets the accuracy and application objective expected,the data transporting rate is up to 20MB/s.
The Design of a Data Acquisition System Based on USB

DAI Hai-feng,FU Cui-yu

DOI: https://doi.org/10.3969/j.issn.1000-0682.2006.04.012

2006-01-01

Abstract:This paper presents the design of a data acquisition system based on the USB interface,which has its rational hardware structure and corresponding software.This system has been put into operation,which has produced a wonderful effect.
Design of a logic analyzer’s continuous trigger module based on FPGA

Sun Jingqi,Wang Houjun,Dai Zhijian

DOI: https://doi.org/10.3969/j.issn.1000-8519.2010.11.009

2010-01-01

Abstract:This article describes a design method of Logic Analyzer’s data acquisition,which is mainly used to analyze embedded software. It is no longer using sampling methods to collect data, but to use the method of instrumentation in software and setting Trigger Word in hardware to monitor the System Bus,When the software run to the Instrumentation point, the hardware generates a trigger and captures the data and time,so, It can accurately capture the valid data. In addition, we use two RAMS to Temporarily store data in FPGA,when one RAM is written,another is read.In this way,we can catch and analyze the real-time data in a long time without interrupting the software running.So ,it can improve the range and quality of analysis of embedded software. Using FPGA in hardware design can improve the system's working speed and Stability. This design has been verified in actual project and achieved good results.
Romote Test System of FPGA based on USB and LVDS

Chen Yixin

DOI: https://doi.org/10.3969/j.issn.1000-8519.2009.04.017

2009-01-01

Abstract:Based on the question of testing FPGA function in special environment,this paper describes a design scheme of FPGA remote test system based on USB interface and LVDS transmission.This scheme applies the Cypress CY7C68013 as USB interface,TI SN65LVDS3x as LVDS remote interface.The FPGA to be tested can also be configured remotely on-line.Moreover,the device driver developed by Jungo WinDriver and the data acquisition application developed by Borland Delphi are provided.The test result show that this scheme has simple structure,amicable interface,stable function and long transmission distance.It provides an efficient experiment measure for FPGA function in special environment.
Design of Laser Echo Data Acquisition System Based on Usb2.0

Shang Fuzhou,Song Yong,Hao Qun,Zhang Kai,Li Meinan,Zhang Wenlong

DOI: https://doi.org/10.1117/12.999931

2012-01-01

Abstract:In this paper, a high-speed data acquisition system based on the technology of USB2.0 (Universal Serial Bus) is designed, in which USB master logic is implemented in an FPGA (Field-Programmable Gate Array). Firstly, the hardware of data acquisition system is discussed, which includes chip selection, data acquisition and transmission circuit and power conversion circuit. Secondly, the corresponding software including USB firmware program, USB device driver and application program as well as its modifications have been described. The designed hardware and software will help to achieve a data acquisition system with the characterstics of high speed and high accuracy, etc.
USB digital I/O device design based On FPGA

Wang Xiaoli,Long Bing,LI Li

DOI: https://doi.org/10.3969/j.issn.1002-7300.2011.10.016

2011-01-01

Abstract:This article from the hardware design and software design two aspects the USB digital I/O device design method.USB 2.0 communication protocol,according to the FPGA logic control as the core control devices,realize the USB interface chip CY7C68013 communication control,multi-channel data storage,read,send and acquisition.More detailed describes the design and realization of the software and hardware equipment,this paper programs.
The Software for the USB-based Multi-Channel Analyzer System

周彤,魏义祥

DOI: https://doi.org/10.3969/j.issn.0258-0934.2002.04.006

2002-01-01

Abstract:A new type of multi-channel analyzer system is introduced in this paper, which takes advantage of Universal Serial Bus to communicate with computer and gets the merit of fast speed, universality and Plug and Play. The main of the article includes the framework of the system, primary functions, display of spectrum date and the way of communication with hardware. The environment of the program is Visual Basic 6.0.
Design and Realization for Portable Vibration Measurement System

WU Dong-dong,ZHAO Gang

DOI: https://doi.org/10.3969/j.issn.1671-1041.2008.03.012

2008-01-01

Abstract:It is described the design and realization of a vibration measurement system based on USB 2.0.In the part of conditioning,with phase locked logic,it realized whole period sampling and adaptive anti-aliasing filtering,and then using CY7C68013A USB 2.0 chip,it realized the interface between acquisition hardware and PC.Afterwards,using visual C++ software calling the functions of measurement studio which has powerful signal analytical functions,developed the application system to synchronously analyze and display waves.In this way,it improved large workload of hardware design,period of develop and ability of extand.
High-Speed Data Acquisition System Base On Usb

Y Wang,Zm Wu,Bf Zhao

2002-01-01

Abstract:The high-speed data acquisition system based on USB (Universal Serial Bus) includes a computer loaded testing platform software, A/D converter, micro-controller and communication interface of USB, and can rapidly and accurately transmit data collected. In circuit design except analogue circuit, memory and microprocessor, nearly all-logical circuit can be realized by PLD (Programmable Logic Device), which improve the system integration, and transform the design of hardware into design of software, and increase the speed of exploitation and reliability of system.
Design of USB-RS232 conversion module based on digital oscilloscope

Guan Ying,Huang Jianguo,Zeng Hao

DOI: https://doi.org/10.3969/j.issn.1002-7300.2010.09.004

2010-01-01

Abstract:With the expansion of USB application,it is very important that to achieve the two-way data communication between USB and the standard industrial interface-RS232.At the same time to facilitate the oscilloscope measurement application of a specific occasion,this paper designed USB-RS232 conversion module based on the digital oscilloscope.In this paper,using ADSP-BF531 as the main controller and CH374S as the USB controller chip to build the hardware design,and designing the software through USB-RS232 converter to achieve a serial communication between the digital oscilloscope and the PC.Using USB interface of digital oscilloscope and the RS232 interface of PC to communicate test,the experiment result shows that is the stable and reliable communication.The method can be referenced when developing the communication between the digital oscilloscope and other RS232 interface devices.
Design of Four-Channel High Precision Data Acquisition System with USB Interface

XUE Feng,LI Bin

DOI: https://doi.org/10.3969/j.issn.1000-3630.2007.05.025

2007-01-01

Abstract:The design of data acquisition system with high speed and high precision,which is based on USB (Universal Serial Bus),is introduced in this paper. A new audio A/D chip AKM5394 is applied to the data acquisition system. Using CPLD,FIFO,USB interface chip and two AKM5394,a four channel data acquisition system with high precision is implemented. The data are also saved and displayed in real time by USB interface on computer. The driving program,which is used for Windows 2000 or Windows XP,and the application program of the system are realized in Visual C++ language,and the firmware codes are programmed in C language. Because of low cost and a high performance,the system with a measuring precision up to 22 bit can be widely used in such fields as measuring control,signal analysis,and so on.
Designs of the High-speed Data Acquisition System Based on USB and I2S Bus

LI Long-yu,FENG Zhi-hua,LIU Zhi-gang,ZHANG Chang-hui

DOI: https://doi.org/10.3969/j.issn.1001-2257.2005.05.016

2005-01-01

Abstract:This paper addresses a frame of highspeed data acquisition system which based on USB and I~2S bus.The using of highspeed data acquisition chip AD7862 and CPLD(complex programmable logic device) make the system adjustable.This method may be a good way for the D/A、DI/DO etc.
The design and realization of instantaneous wave recorder based on USB2.0.

GAO Hui,YU Li-zhen,WANG jin-xiang,WANG Wei-bing

DOI: https://doi.org/10.3969/j.issn.0258-0934.2006.06.023

2006-01-01

Abstract:The paper discusses a design of an instantaneous wave recorder based on USB2.0 interface.The sample rate supported is 100MSPS and the sample precision is 10 bits.It summarizes on the design of the firmware、windows drivers and the application program based on LabVIEW.
A data acquisition system based on usb2.0

Dai Guan-zhong

2005-01-01

Abstract:A data acquisition system based on USB2.0 is this paper, including the designing of hardware, firmware, drivers and application programs is presended. This system can realize analog signal sampling in 8 channels simultaneously and the input and output of switching signal in 16 binary channels. The USB interface control chip adopted is CY7C68013, a product of the Company of Cypress. Through designing the control logic of its GPIF interface, sampling and transmiting with high speed have been realized.

Design and Realization of Virtual Logic Analyzer Based on USB2.0 Bus

Design and Implementation of the High-Performance Link Layer in High-Speed Serial Communication

Design of Data Communication Interface of Data Acquirement System Based on USB

Design of USB2.0 Protocol Analyzer Based on FPGA

Design of high speed data sampling system based on FPGA and USB2.0

USB Visual Oscilloscope Based on FPGA

Design and Realization of Low Cost USB Protocol Converter

Designs of USB2.0 interface of data acquisition card

The Design of a Data Acquisition System Based on USB

Design of a logic analyzer’s continuous trigger module based on FPGA

Romote Test System of FPGA based on USB and LVDS

Design of Laser Echo Data Acquisition System Based on Usb2.0

USB digital I/O device design based On FPGA

The Software for the USB-based Multi-Channel Analyzer System

Design and Realization for Portable Vibration Measurement System

High-Speed Data Acquisition System Base On Usb

Design of USB-RS232 conversion module based on digital oscilloscope

Design of Four-Channel High Precision Data Acquisition System with USB Interface

Designs of the High-speed Data Acquisition System Based on USB and I2S Bus

The design and realization of instantaneous wave recorder based on USB2.0.

A data acquisition system based on usb2.0