The Design of a Data Acquisition System Based on USB

DAI Hai-feng,FU Cui-yu

DOI: https://doi.org/10.3969/j.issn.1000-0682.2006.04.012

2006-01-01

Abstract:This paper presents the design of a data acquisition system based on the USB interface,which has its rational hardware structure and corresponding software.This system has been put into operation,which has produced a wonderful effect.

What problem does this paper attempt to address?

Design of Data Communication Interface of Data Acquirement System Based on USB

陈章位,赵玉刚

DOI: https://doi.org/10.3321/j.issn:1004-132X.2004.20.014

2004-01-01

Abstract:An interface based on USB is designed for Data Acquirement System with DSP chips. Cypress EZ-USB technology and FPGA technology were used in this interface. This kind of interface can achieve high speed data communication between the Data Acquirement System and the PC in the USB 1.1 protocol, and it can meet the requirements of high speed and real-time requirements.
Data Acquisition System Based on USB Bus

宁蕴绯,张宇翔,郭敏

DOI: https://doi.org/10.3969/j.issn.1008-0570.2008.16.029

2008-01-01

Abstract:A design scheme of data acquisition based on USB Bus and it s hardware and software implementation are introduced. As a new computer bus interface criterion,USB applies to the high -speed data acquisition system.This article introduces the USB con-nection technology in the testsurvey,the success has developed a set of practical portable multi-purpose high speed data acquisition system. The paper introduces the design of data acquisition system based on USB interface,including hardware design,firmware design, driver design based on WDM and internet applications design.
Design of Four-Channel High Precision Data Acquisition System with USB Interface

XUE Feng,LI Bin

DOI: https://doi.org/10.3969/j.issn.1000-3630.2007.05.025

2007-01-01

Abstract:The design of data acquisition system with high speed and high precision,which is based on USB (Universal Serial Bus),is introduced in this paper. A new audio A/D chip AKM5394 is applied to the data acquisition system. Using CPLD,FIFO,USB interface chip and two AKM5394,a four channel data acquisition system with high precision is implemented. The data are also saved and displayed in real time by USB interface on computer. The driving program,which is used for Windows 2000 or Windows XP,and the application program of the system are realized in Visual C++ language,and the firmware codes are programmed in C language. Because of low cost and a high performance,the system with a measuring precision up to 22 bit can be widely used in such fields as measuring control,signal analysis,and so on.
The Design of USB Data Acquisition System Based on CH371

ZHANG Xiao-guang,XU Bao-guo

DOI: https://doi.org/10.3969/j.issn.1006-7167.2005.06.013

2005-01-01

Abstract:This paper introduced the design of a data acquisition system based on USB which included hardware and software. Due to the CH371 applied in the system, the firmware procedure' program was simplified for carrying out USB message and the time of the system development was shortened. The result shows that it is preferable to meet the demand of data acquisition in lab.
Real-time Bidirectional Data Transmission Based on USB Interface

Kuang Wang

2005-01-01

Abstract:The article designs a real-time bidirectional transmission channel.And it introduces the theory of the design,selects specific chip,introduces the hardware of the channel,and brings forward the method of designing USB firmware,driver,and application.
Design of the High Speed Real-time Data Acquisition System Based on USB 2.0

WANG Ping,SU Tao,FANG Haojun

DOI: https://doi.org/10.3969/j.issn.1004-373x.2007.01.029

2007-01-01

Abstract:To collect data and send the processed data to the PC in high speed,we design a high speed real-time data acquisition system based on USB 2.0.The paper introduces the hardware design of the system,the emphasis introduces the design of the firmware,driver and application program of the ISP1581.The system could complete data acquisition,processing and transmission very well,which is proved on a high speed DSP platform.
A Data Acqusition System Based on DSP and USB

JIANG Chao,LI Pei-yu

DOI: https://doi.org/10.3969/j.issn.1001-3881.2005.01.057

2005-01-01

Abstract:The structure of a data acquisition system based on DSP and USB chips was described.The interface between different modules was introduced,and the design of firmware used in USB was described.
Data Acquistion Device Based on USB Bus and Application

Wenquan Wang

2005-01-01

Abstract:The traditional data acquisition system based on board card has many disadvantages,for example,it is not easily toted and has bad compatibility of the hardware.In order to resolve the above disadvantages,we design and realize a data acquisition system based on USB Bus.This paper also introduces simply its applications.
Application of USB in the Data Acquisition System

杜德生,李树林

DOI: https://doi.org/10.3969/j.issn.1003-7241.2008.09.037

2008-01-01

Abstract:As the developing of computer and information techniques,the data acquisition system combined with advanced electronic techniques could process vast data by software.Universal Serial Bus(USB) which has been the PC-standard provided a lot of convenience for data collection.Using the USB can achieve more effective,more economic more points of data collection than traditional methods.This paper discusses the use of USB interface to achieve multipoint data acquisition.
A data acquisition system based on usb2.0

Dai Guan-zhong

2005-01-01

Abstract:A data acquisition system based on USB2.0 is this paper, including the designing of hardware, firmware, drivers and application programs is presended. This system can realize analog signal sampling in 8 channels simultaneously and the input and output of switching signal in 16 binary channels. The USB interface control chip adopted is CY7C68013, a product of the Company of Cypress. Through designing the control logic of its GPIF interface, sampling and transmiting with high speed have been realized.
Design and Application of Data Acquisition System Based on TMS320F2812 and USB

ZHANG Feng-jiang,WANG Xing-song

DOI: https://doi.org/10.3969/j.issn.1672-6413.2007.02.026

2007-01-01

Abstract:A multichannel data acquisition system was designed based on digital signal processor(DSP) and universal serial bus(USB) technology.The structure of the hardware and software was introduced,and the method of realization was described,the function was analysed.
High-Speed Data Acquisition System Base On Usb

Y Wang,Zm Wu,Bf Zhao

2002-01-01

Abstract:The high-speed data acquisition system based on USB (Universal Serial Bus) includes a computer loaded testing platform software, A/D converter, micro-controller and communication interface of USB, and can rapidly and accurately transmit data collected. In circuit design except analogue circuit, memory and microprocessor, nearly all-logical circuit can be realized by PLD (Programmable Logic Device), which improve the system integration, and transform the design of hardware into design of software, and increase the speed of exploitation and reliability of system.
Design of Data Acquisition System Based on LabWindows/CVI and USB2.0

WANG Hai-tao,CHEN Hou-jin

DOI: https://doi.org/10.3969/j.issn.1005-8451.2012.10.001

2012-01-01

Abstract:Since there was a lack of flexibility and real-time,the High Speed Data Acquisition System was designed based on LabWindows/CVI.The System used USB2.0.LabWindows/CVI was chosen to build the software platform of the System.Dynamic Linking Library(DLL) was used to implement the communication between the host computer and the System.The real-time data acquisition was implemented by the multithreading of LabWindows/CVI.The result showed that the System was with advantages,such as debugging easily,friendly interface,high real-time,stable running,and it could be widely accepted.
A Novel Research of USB Data Acquisition System

ZHANG Huaiqiang,ZHOU Jianbin,PAN Shibin,HE Weimin

2007-01-01

Abstract:This paper describes how to realize a real-time data acquisition system based on powerful MCU C8051F020,and its design of hardware and software.The original signal will be amplified by a internal unit PGA(programmable control amplifier), and than will be processed by the 100 ksps successive close ADC.The final data will be transmitted to a PC through a bridge CP2101 which can pass data form UART to USB interface.In order to display and analyze the signal and the USB supplies power to the system.Finally,the system uses ADC to acquire signal which is from temperature sensor,for the sake of substantiating the reliability and stability of the system.
Design of USB Data Acquisition System Based on SCM

李博,祖静

2008-01-01

Abstract:This paper describes how to realize a real-time data acquisition system based on C8051F020, and its design of hardware and software. The technical characteristic of the C8051F020 single chip machine and the ch375 USB chip is given. The original signal will be amplified by a internal unit programmable control amplifier, the C8051F020 single chipmachine is used as the processor, and it can achieve the writing and reading of the storage medium, such as a USB flash drive, through the control ofCH375 USB chip, the program designing is also realized in this paper.
Designs of USB2.0 interface of data acquisition card

Qiao Liyan,Wu Jiangwei,Xu Hongwei

DOI: https://doi.org/10.3969/j.issn.1002-7300.2010.01.017

2010-01-01

Abstract:Data acquisition has been widely used in industrial production.Based on summarization of the hardware architecture,the thesis gives a detailed description of the design of USB interface,including the hardware design of USB2.0,The interface logic design in FPGA,USB firmware design,USB driver program design,and the application design.Through the experimental test,the result proves the design meets the accuracy and application objective expected,the data transporting rate is up to 20MB/s.
A Data Collection System Based on USB Interface

XIONG Kaisheng,DONG Zhaoxin

DOI: https://doi.org/10.3969/j.issn.1674-4888.2006.10.026

2006-01-01

Abstract:With the popularization and development of USB(Universal Serial Bus) interface,how to make use of the USB interface to realize data collection now becomes a hotspot of research and development.Realization concept of data collection system based on USB and implementation with microprocessor with embedded USB interface are presented and the hardware design and software development are discussed.On the part of hardware design,this article provides three schemes and introduces one among this three schemes in detail.On the part of software development,this article introduces the USB firmware design,USB device drive program design and application program design in detail.
Design on autos running parameter acquisition system based on USB host

Ming-zhu LIU,Li-ling HE,Li-wei GE

DOI: https://doi.org/10.3969/j.issn.1672-0946.2005.01.018

2005-01-01

Abstract:To realize the measure of automobile running parameters and the storage of mass acquired data, a new data acquisition system is designed by analyzing the protocol of Universal Serial Bus (USB) in this paper. It uses the embedded USB Host technology as the emphasis of the design, and uses USB movable disk as its memory device. This paper also gives the design principle, circuit structure, special data communication drivers and applied programs. This system implements the efficient data communication in the USB Host controller, the operations of data acquisition and the data transmission in high speed, and it can realize the function of data acquisition, memory, display and inquiry. The system can work efficiently under severe condition, and it also has excellent compatibility and expansibility because of the modularity design.
Computer Data Acquisition Software System for Vernier Caliper Base on USB Interface

杜喜鹏,刘桂雄,洪晓斌

DOI: https://doi.org/10.3969/j.issn.1671-3133.2009.06.023

2009-01-01

Abstract:In order to achieve the real-time flexible data processing of the vernier caliper measurements,the vernier caliper data acquisition system based on USB interface is developped.Focuses on introducing the design and realization of the three functional modules such as USB interface communications,data acquisition and data storage management.Finally,the data acquisition system is put into use in measuring the size of the workpiece.The results showed that the system has the features such as rapid data acquisition,high reliability and flexibility.
Design of data acquisition device driver based on USB bus

Zang Julun,Zhu Changqing,Wang chuanchuan,Jiang Shaofei

DOI: https://doi.org/10.3969/j.issn.1002-8978.2009.12.018

2009-01-01

Abstract:Combine to the data acquisition device based on USB bus,It introduced operational principle,design principle and design method of WDM driver.It also gave a driver routine for implementing USB bulk transfer,Introduced the routine's every functional module.It has stable function,reliable transmission.It has already been applied to data acquisition device.The testing results of the system function has been proved that the data transmission procedure coming to the design request.The detailed instruction for the design procedure of the driver program is useful for design of special USB device driver in practice.

The Design of a Data Acquisition System Based on USB

Design of Data Communication Interface of Data Acquirement System Based on USB

Data Acquisition System Based on USB Bus

Design of Four-Channel High Precision Data Acquisition System with USB Interface

The Design of USB Data Acquisition System Based on CH371

Real-time Bidirectional Data Transmission Based on USB Interface

Design of the High Speed Real-time Data Acquisition System Based on USB 2.0

A Data Acqusition System Based on DSP and USB

Data Acquistion Device Based on USB Bus and Application

Application of USB in the Data Acquisition System

A data acquisition system based on usb2.0

Design and Application of Data Acquisition System Based on TMS320F2812 and USB

High-Speed Data Acquisition System Base On Usb

Design of Data Acquisition System Based on LabWindows/CVI and USB2.0

A Novel Research of USB Data Acquisition System

Design of USB Data Acquisition System Based on SCM

Designs of USB2.0 interface of data acquisition card

A Data Collection System Based on USB Interface

Design on autos running parameter acquisition system based on USB host

Computer Data Acquisition Software System for Vernier Caliper Base on USB Interface

Design of data acquisition device driver based on USB bus