Abstract:The constitutive behavior of AA7075 aluminum sheet like other metallic sheet materials is highly temperature and strain rate dependent at elevated temperatures. The uniaxial tensile test is commonly employed to characterize the temperature and strain rate dependent deformation behavior. However, the traditional uniaxial tensile testing and data analysis procedure treats the gauge length of sample as a uniformly-deforming (or homogeneous) region. This may not be accurate due to early localized deformation that is initiated in the gauge region at elevated temperatures. Treating the post-necking hardening behavior of uniaxial tensile samples has been an important task to expand the effective range of true stress-true strain curves at elevated temperatures for metal and alloys. To explore this issue, uniaxial tensile tests on AA7075-F sheets (with as-fabricated temper) were conducted at 673o K and four different test speeds. The test procedure also utilized an on-line 2-D digital image correlation (DIC) system method to obtain full-field strain map from the deforming gauge region of the test specimen. Local stress-strain curves at different points along the gauge length were then calculated based on the recorded local in-plane principal stress and strain values from macroscopic force data and current cross-section of the specimen at the chosen points. In this manner, the DIC strain analysis not only enabled the determination of stress-strain response but also the determination of strain rates at specific chosen points along the gauge length. The local stress-strain curves revealed significant deviation at an earlier stage of deformation from the global (or macroscopic) stress-strain response based on the entire gauge region. To estimate the constitutive behavior at different strain rates, a correction method to traditional stress-strain curves was applied to obtain a family of stress-strain curves at different constant strain rates based on the local stress-strain curves. Additionally, the material deformation response in the stress, strain and strain rate space in the 3D Cartesian coordinate system was also constructed for tests conducted at different stretching speeds. Further, a verification test was conducted to see if the above methodology could provide an accurate estimation of local deformation behavior of AA7075 sheet. Furthermore, the above experimental method was also coupled with the Gurson-Tvergarrd-Needleman (GTN) ductile void damage model and incorporated into ABAQUS-Explicit general purpose finite element (FE) analysis code via a VUMAT material subroutine. Good agreement was obtained for both the local and global stress-strain curves between the FE test simulation and experimental stress-strain results. The proposed experimental methodology and the resulting stress-strain-strain rate behavior is believed to be applicable in describing the strain rate-dependent constitutive behavior of AA7075-F sheet metals at 673o K.

Stress-strain relationship and physical-mechanical properties of domestic structural aluminum alloy

Mean Stress Relaxation During Low-cycle Fatigue of Aluminum Alloy 7050-T7451

A study on the mean stress relaxation behavior of 2124-T851 aluminum alloy during low-cycle fatigue at different strain ratios

Full-Range Stress–Strain Curves for Aluminum Alloys

Strain Ratio Effects on Low-Cycle Fatigue Behavior and Deformation Microstructure of 2124-T851 Aluminum Alloy

Study on Correlation Between Parameters of "single Factor" Constitutive Model and Temperature for 7050 Aviation Aluminum-Alloy

Test Studies on Fatigue Performance of Aluminum Alloys Used in Construction

Constitutive Modeling on Cyclic Stress-Strain Behaviour of 7A04-T6 High-Strength Aluminium Alloy

Study on constitutive relationship of 6061 aluminum alloy based on Johnson-Cook model

Experimental Investigation and FE Analysis on Constitutive Relationship of High Strength Aluminum Alloy under Cyclic Loading

Experimental and numerical investigation on plasticity and fracture behaviors of aluminum alloy 6061-T6 extrusions

Study on Mechanical Properties and Constitutive Model of 5052 Aluminium Alloy

Dynamic Mechanical Properties and Modification of Fracture Criteria of 6061-T651 Aluminum Alloy

Local and global tensile deformation behavior of AA7075 sheet material at 673oK and different strain rates

Experimental and Physical-Based Constitutive Model Study of Fcc Metal over Wide Temperature and Strain Rate Ranges

Research and Revise on Constitutive Equation of 7050-T7451 Aluminum Alloy in High Strain Rate and High Temperature Condition

Study of dynamic mechanical behavior of 1060-H112 aluminum alloy: Experimental and numerical simulation

Deformation responses and fracture behaviors of AA6061 under different stress triaxialities

Comparative Analysis Between Stress- and Strain-Based Forming Limit Diagrams for Aluminum Alloy Sheet 1060

Study on Constitutive Model of Cyclic Elastoplastic Behavior of 6082-T6 Aluminum Alloy

Damage analysis of aluminum alloy gusset joints under cyclic loading based on continuum damage mechanics