Abstract:The chemical-vapor-deposition (CVD) process is sufficiently well developed to allow the large-scale production of carbon nanotubes (CNTs). Metal nanoparticles (Fe, Co, Ni, etc.) are usually immobilized on a solid support and then decompose the gaseous hydrocarbon feedstocks into fragmented carbon units at elevated temperatures of 700-1100°C. Metal carbides are formed and then these dominate the growth of filamentous carbon as a structural template. The produced CNTs cannot stay firmly with an inert support and so inevitably detach away, especially during liquidphase purification or mechanical treatment. The biggest difficulties when handling the loose powder are filtration in the slurry-phase operations and the large pressure drops in fixed-bed reactors. These problems very much limit the application of CNTs on a large scale. The fabrication of carbon filaments on a structured support (e.g., activated carbon, carbon fibers, porous frameworks, graphite) has also suffered from discontinuities in the structure. The future use of CNTs has also been restricted by the technical requirements and the necessary high energy consumption to operate the intense and complicated CVD process. To avoid any mechanical post-treatment of powder and the risk of explosion during CVD synthesis, we have explored a simple method to produce monolithic CNTs directly as millimeter-scale spheres, featuring an integral continuity in the structure from microscopic to macroscopic scales. The whole process of CNTs growth has been conducted in a flow of ultrapure N2, involving a set of elementary steps in the solid phase being less complex than the widely used CVD process. The growth of CNTs is based on a solid reaction mechanism and well-graphitized nanotubes can be obtained even at a temperature as low as 400C. Direct observation of all growth events is made by using in-situ transmission electron microscopy (TEM), X-ray diffraction (XRD), IR, Raman spectroscopy and thermogravimetric analysis. A commercial styrene-divinylbenzene copolymer resin was used as the carbon precursor. According to Scheme 1, the ion-exchanged resin spheres were calcined at 800C in a flow of N2 or vacuum, after which the average diameter decreases from 0.77 to 0.49 mm, while the bulk density increases from 0.55 to 0.91 g ml. A novel macroscopic structure can be clearly seen, especially after the removal of the Fe nanoparticles and the amorphous carbon species by refluxing the spheres in concentrated HNO3. As seen in Fig. 1a, the twisted nanotubes construct the monolith while keeping a spherical shape. The cross-section views of the hand-broken spheres show no difference in the structure between the bulk and the surface, indicating a homogeneous distribution of the nanotubes in the millimeter-scale spheres (Fig. 1b). The nitrogen adsorption/ desorption isotherm shows a hysteresis loop to identify a typical mesoporous feature. The measured BET surface area and the pore volume are 223.7 m g and 0.42 ml g, respectively. The distribution of the pores ranges between about 2 and 15 nm.

Fabrication of Micrometer-Scale Spherical Titanate Nanotube Assemblies with High Specific Surface Area

Structure-tunable Synthesis and Structural Stabilities of the Multilayered Titanate Nanotube Thin Films Grown on Titanium Metal Surface

One-Step Hydrothermal Synthesis and Characterizations of Titanate Nanostructures

Synthesis and characterization of high-aspect-ratio titania nanotubes

Synthesis of Tubular Titanate Via a Self-Assembly and Self-Removal Process

Synthesis of One-Dimensional Sodium Titanate Nanostructures.

Templated Synthesis of TiO2 Nanotube Macrostructures and Their Photocatalytic Properties

Self-assembled titanium-based macrostructures with hierarchical (macro-, micro-, and nano) porosities: A fundamental study

Large-scale synthesis of titanate and anatase tubular hierarchitectures.

Hydrothermal Synthesis, Characterization and Formation Mechanism of Self-Assembled Mesoporous SrTiO3 Spheres Assisted with Na2SiO3·9H2O

Spherical Multi-Walled Carbon-Nanotube Architectures : Formation Mechanism and Catalytic Performance

Solvothermal Growth of Three-Dimensional TiO2 Nanostructures and Their Optical and Photocatalytic Properties

A Simple Solvothermal Process to Synthesize CaTiO3 Microspheres and Its Photocatalytic Properties

Template-free Hydrothermal Synthesis of Macroporous TiO2 Microspheres on a Large Scale

Plate, wire, mesh, microsphere, and microtube composed of sodium titanate nanotubes on a titanium metal template

Synthesis and Characterization of Ion-Exchangeable Titanate Nanotubes

Preparation and characterization of titanium oxide nanotubes

Hydrothermal growth of multi-facet anatase spheres

Synthesis and Growth Mechanism of Lead Titanate Nanotube Arrays by Hydrothermal Method

Directed growth of TiO<sub>2</sub> nanorods into microspheres

Structure and applications of titanate and related nanostructures