Abstract:Large residual stresses in a laser-cladded surface coating over a metal part are detrimental to its mechanical integrity and fatigue life. In this study, a three-dimensional uncoupled thermo-mechanical finite element model was developed to predict (a) the evolution of the temperature field in a direct diode laser hot-wire multi-track cladding process and (b) associated thermally induced residual stress distribution in laser-cladded 316L stainless steel coatings on the A36 mild steel substrate. The thermal analysis of the finite element model of the laser cladding process was first validated by the time-resolved temperature measurements using thermocouples placed on the mild steel surface near the clad layer. The stress analysis of the finite element model during the cooling stage was then validated by the spatially-resolved X-ray diffraction measurements of residual stresses in the clad layer. The experimentally validated finite element model was then applied to investigate the effect of laser power, material properties (Young's modulus, yield strength, and coefficient of thermal expansion), and the number of clad tracks on the residual stresses in the clad layer. It was found from the numerical simulations that the magnitude of residual stress components increases with increasing Young's modulus, yield strength, and coefficient of thermal expansion of the clad material. A higher temperature gradient located in the molten pool induced a higher concentration of thermal stresses and eventually a higher residual stress level in the clad samples. Higher tensile residual stress was generated with an increasing number of clad tracks although the residual stress in the existing clad tracks was relaxed somewhat during the subsequent cladding process of new tracks. Specifically, high tensile transverse residual stress formed in the overlapped region and on both sides of the clad layer, whereas higher longitudinal and von Mises equivalent residual stresses were developed in the last clad track. The finite element analysis results presented in this study may provide useful guidance for reducing the residual stresses in clad layers by optimizing the multi-track laser cladding processing parameters.

WITHDRAWN: FEM prediction of surface characteristics after laser transformation hardening

Experimental Characterization and Strengthening Mechanism of Process-Structure-property of Selective Laser Melted 316 L

Experimental Characterization and Yield Strength Model for Process-Structure-Property of Selective Laser Melted 316L

FEM Analysis of Laser Hardening with Different Laser Moving Velocities

Effect of distribution status of the spot matrix on tensile behavior for 42CrMoV when conducting discrete laser surface strengthening: Based on experiment and simulation

Effect of Surface Modification on the High Temperature Low Cycle Fatigue Performance of LPBF 316L Austenitic Steel

Process-structure-property Modeling for Postbuild Heat Treatment of Powder Bed Fusion Ti-6Al-4V

Understanding Orientation-Dependent Plasticity in Laser Beam Powder Bed Fusion Stainless Steel Through Crystal Plasticity Modelling

Residual Stress Prediction for a Coated Tunnel Boring Machine Cutter considering the Effects of Heat Treatment and Laser Cladding

A thermo-metallurgical-mechanical model for microstructure evolution in laser-assisted robotic roller forming of ultrahigh strength martensitic steel

Numerical simulation of two-track laser hardening process of 42CrMo steel

Thermal mechanical modeling and residual stress prediction for laser direct energy deposition of 30CrNi2MoVA steel considering solid-state phase transformation

Stress evolution mechanism during laser welding of ultra-high-strength steel: considering the effects of temperature sensitivity, strain hardening and annealing

Numerical and experimental study on thermal-metallurgical-mechanical behavior of high-strength steel welded joint

Crystal plasticity quantification of laser peening strengthening effects on AA2195-T6 friction stir welded joints

Phase-field simulation and high-temperature confocal laser scanning microscope experimental study of Martensite transformation during the disk laser quenching process

Response of laser power bed fusion manufactured austenitic stainless steel towards combined heat treatment and low-temperature thermochemical surface strengthening

Study on Multi-Field Coupled Evolution Mechanism of Laser Irradiated 40Cr Steel Quenching Process Based on Phase Change Induced Plasticity

A 3D finite element analysis of thermally induced residual stress distribution in stainless steel coatings on a mild steel by laser hot wire cladding

A Comprehensive Transformation-Thermomechanical Model on Deformation History in Directed Energy Deposition of High-Speed Steel

Laser-induced softening analysis of a hardened aluminum alloy by physical simulation