Abstract:The ambition of carbon neutrality has become a common pursuit for researchers worldwide, and hydrogen as a green and clean energy carrier is expected to contribute to this achievement. Since hydrogen fuel cell vehicles require a high input hydrogen pressure, compressors in hydrogen refueling stations are thus indispensable for the large-scale application of hydrogen energy . Compared to conventional mechanical hydrogen compressors, metal hydride based hydrogen compressors have the advantages of high security and low cost, providing a viable solution for hydrogen refueling station development. Herein, two series of Ti 0.95 Zr 0.07 Cr 1.3- x Mn x Fe 0.4 ( x = 0.2, 0.3, 0.4, 0.6) and Ti 0.95 Zr 0.07 Cr 1.0 Mn 0.6 Fe 0.4- y Cu y ( y = 0.1, 0.15, 0.2, 0.3) alloys were designed to achieve 8–22 MPa hydrogen compression in water bath at 283–353 K. All the as-prepared alloys exhibit the single hexagonal C14 Laves phase structure. In particular, the double substitution of Cr and Fe by Cu and Mn elements in Ti–Zr–Cr–Mn–Fe alloy can enlarge its hydrogen storage capacity without varying the equilibrium pressure. For instance, Ti 0.95 Zr 0.07 Cr 1.0 Mn 0.6 Fe 0.25 Cu 0.15 alloy has a hydrogenation plateau pressure of 6.16 MPa at 283 K and a dehydrogenation plateau pressure of 24.23 MPa at 353 K, with the max hydrogen capacity of 1.72 wt%. Furthermore, the relative high density molding method of metal hydride bed with 20 g of alloy powder was developed. The binder epoxy resin and the thermal conductor flake graphite were selected and added into the alloys to form metal hydride compacts (MHCs). The structural stability of modified MHCs can be enhanced due to the formation of a three-dimensional grid structure, with a higher resistance to pulverization and degradation. The improved thermal conductivity involving a filling compact strategy can significantly shorten hydrogenation reaction time by 50% and lower the abrupt temperature of metal hydride bed by 20 K with excellent stability over 100 cycles, and provide new insights of the development of safe and efficient hydride hydrogen compressor.

Metal Hydride Beds and Hydrogen Supply Tanks As Minitype PEMFC Hydrogen Sources

Development of Ti–Zr–Mn–Cr-(V–Fe) Based Alloys for Hydrogen Feeding System in Hydrogen Metallurgy Application

Development of RE-based and Ti-based Multicomponent Metal Hydrides with Comprehensive Properties Comparison for Fuel Cell Hydrogen Feeding System

Preparation and Properties of Mg-based Hydrogen Storage Alloys for Hybrid Electric Vehicle

Hydrogen Storage Properties of Ti-Cr-Mn-M (M=V, Fe, Ni, Cu) Alloys

Hydrogen Storage Properties and Application of the Alloy Ml-Ca-Ni in a Hydrogen-Gasoline Hybrid Fuel Bus

Hydrogen storage properties of TiMn1.5V0.2-based alloys for application to fuel cell system

Optimal design and simulation investigation for high-density hydrogen storage tanks filled with rare earth-based (RE-Ca)(Ni-Co) 5 optimized alloy

Advanced high-pressure metal hydride fabricated via Ti–Cr–Mn alloys for hybrid tank

Hydrogen storage alloys for high-pressure suprapure hydrogen compressor

A 70 MPa Hydrogen-Compression System Using Metal Hydrides

Low-cost Vanadium-Free Ti–Zr–Cr–Mn–Fe Based Alloys for Metal Hydride Hydrogen Compressor under Mild Conditions

Research and application of Ti–Mn-based hydrogen storage alloys

Experimental and numerical study of metal hydride beds with Ti0.92Zr0.10Cr1.0Mn0.6Fe0.4 alloy for hydrogen compression

Metal Hydride Storage Systems: Approaches to Improve Their Performances

Study on Ti-Mn/Ti-Cr Hydrogen Storage Alloys for Hydride Hydrogen Compressor

Development of Ti1.02Cr2-x-yFexMny (0.6≤x≤0.75, Y=0.25, 0.3) Alloys for High Hydrogen Pressure Metal Hydride System

Laves phase double substitution alloy design and device filling modification for Ti-based metal hydride hydrogen compressors

Performance of Ti-Mn Multicomponent Alloy and Hydride Air Conditioner with Composite Hydride Beds Used for Auto

An investigation of the mechanical behaviour of hydrogen storage metal beds on hydriding and dehydriding and several methods of preventing the damage of hydride containers caused by the expansion of hydrogen storage metals

Hydrogen storage performances, kinetics and microstructure of Ti<sub>1.02</sub>Cr<sub>1.0</sub>Fe<sub>0.7-x</sub>Mn<sub>0.3</sub>Al<su b>x</sub> alloy by Al substituting for Fe