Abstract:Selective laser melting (SLM) has been widely used to manufacture customised metallic parts because it provides an integrated way to manufacture three-dimensional (3D) parts from computer-aided design models after several sub-processes. On the other hand, aluminium-based nanocomposites are widely used in the aerospace and automotive industries due to their light weight, high specific strength, excellent wear resistance, but their manufacturability and mechanical properties are not well understood when these new materials are employed in SLM. This is an important consideration because, compared with traditional manufacturing technologies, SLM offers the ability to manufacture engineering parts with very complex geometries by employing a layer-by-layer manufacturing principle. Hence, this thesis systematically studies the SLM of an advanced Al-Al2O3 nanocomposite that is synthesised using high-energy ball-milling (HEBM) process. The aim of this study is to use SLM to fabricate a nearly full dense Al-Al2O3 nanocomposite composed of 96 vol.% Al and 4 vol.% Al2O3 powder. The synthesis and characterisation of ball-milled powder is the first contribution of this study, which also investigates the influence of milling and pause duration on the fabrication of ball-milled composite powder. The second contribution of this work is the development of a 3D finite element model to predict the thermal behaviour of the first layer’s composite powder. Both the transient temperature distribution and molten pool dimensions are predicted within the laser scanning, which VI enables a more efficient selection of the process parameters (e.g. hatch spacing and scanning speed). The third contribution of this study is the optimisation of the SLM process parameters and microstructure investigation of the fabricated samples. The optimum laser energy density and scanning speed that are used to fabricate nearly full dense Al-Al2O3 nanocomposites are found to be 317.5 J/mm3 and 300 mm/s, respectively. The relative density is evaluated by quantifying the porosity on both the horizontal and vertical sections. The fabricated composite parts were observed to exhibit a very fine granular-dendrite microstructure due to the rapid cooling, while the thermal gradient at the molten pool region along the building direction was found to facilitate the formation of columnar grains. The final contribution of this study is the investigation of mechanical properties such as tensile strength, microhardness and macro and nanoscale wear behaviour. Compared to pure Al, the addition of 4 vol.% Al2O3 nanoparticulates was found to contribute to a 36.3% and 17.5% increase in the yield strength and microhardness of the composite samples, respectively. Cold working was found to contribute to a 39% increase in microhardness due to grain deformation. The pin-on-disc wear testing and atomic force microscopy (AFM) nanoscratching were performed to study the macro and nanoscale wear behaviour of the fabricated samples, respectively.

An investigation of laser-assisted machining of Al2O3 particle reinforced aluminum matrix composite

An Experimental Investigation on Ultrasonic Vibration-Assisted Grinding of Sio2f/Sio2 Composites

Mechanisms involved in the tool life improvement of laser assisted machining 45%SiCp/Al composites

Investigation on the machinability of SiCp/Al composite by in-situ laser assisted diamond cutting

Laser Based Machining of Aluminum Metal Matrix Composites

Experimental and FEM study of surface formation and deformation mechanism of SiCp/Al composites in laser-ultrasonic vibration assisted turning

Study on the processing performance of 60% SiCp/Al composite materials assisted by longitudinal and torsional ultrasonic vibration milling

Micro-milling of 65 vol% SiCp/Al composites with a novel laser-assisted hybrid process

Investigation on the impact of thermal softening effect induced by nanosecond pulsed laser-assisted cutting on the deformation mechanism of SiCp/Al composites

Finite element analysis and experimental study on the cutting mechanism of SiCp/Al composite in laser ultrasonic elliptic vibration turning

Microstructure evolution and mechanical properties of Al-Al2O3 composites fabricated by selective laser melting

Study on Machinability of SiCp/Al Composites by Laser-Induced Oxidation-Assisted Turning

Experimental study on grinding process of Al-Mg2Si aluminum matrix composites

Overview of research on machining mechanism of aluminum-based silicon carbide composites (SiCp/Al)

Selective laser melting of an advanced Al-Al2O3 nanocomposite

High speed, high power density laser-assisted machining of Al-SiC metal matrix composite with significant increase in productivity and surface quality

Experiment Research on Cutting Performance of High Volume Fraction SiCp/Al Composites in Rotary Ultrasonic Machining

Experimental study on laser assisted ultrasonic elliptical vibration turning (LA-UEVT) of 70% SiCp/Al composites

Investigation on Electrochemical Jet Machining of High Volume Fraction SiCp/Al Composite

Hybrid-hybrid turning of micro-SiCp/AA2124 composites: A comparative study of laser-and-ultrasonic vibration-assisted machining

Enhanced machinability of SiCp/Al composites with laser-induced oxidation assisted milling