Abstract:Three polyaniline (PANI)/zeolite Y composites with different polyaniline loads, PANI-Y-1, PANI-Y-2 and PANI-Y-3, were prepared by in situ chemical oxidation polymerization method using different amounts of aniline. The structural characteristics of these materials were analyzed by FT-IR and nitrogen adsorption experiment. The adsorption and regeneration properties of the composites for low-concentration CO₂ at atmosphere pressure were investigated. Characterization results show that aniline is successfully polymerized in and out side of channels of zeolite Y. The above three materials, whose pores are composed of macropores and mesopores, have specific surface areas of 52, 54 and 35 m2 g -¹, respectively. In addition, a composite with high polyaniline loading has low pore volumes. At 20°C, CO₂ adsorption on the three composites and zeolite Y are well fitted with the Logistic model, and the adsorption amount of CO₂ with initial concentration of 10% follows an order of PANI-Y-2 (2.09 mmol · g⁻¹) > PANI-Y-3 (1.79 mmol · g⁻¹) > PANI-Y-l (1.07 mmol · g⁻¹) > zeolite Y (0.80 mmol · g⁻¹. The adsorption order of the composites is the result of combined effects from polyaniline amount and specific surface area of adsorbents. With concentrations ranging between 2% and 10% CO2 adsorption amount increases when initial concentration is raised. With adsorption temperature changing from 25° to 6°C, low temperature is advantageous to enhancing CO₂ adsorption. For PANI-Y-2, only a low regeneration efficiency of 68% is obtained after four times thermal desorption at 80°C. However, the regeneration efficiency could be increased up to 94% by aqueous ammonia combined with thermal treatment method.

Gas-Response Studies of Polyaniline Composite Film Containing Zeolite to Chemical Vapors

Polyaniline–TiO2 Nano-Composite-based Trimethylamine QCM Sensor and Its Thermal Behavior Studies

The Research and Application of Polyaniline/Multi-Walled Carbon Nanotubes Composite Sensitive Membrane for Ammonia Gas Detection

Preparation of Polyaniline–tio2 Composite Film with in Situ Polymerization Approach and Its Gas-Sensitivity at Room Temperature

Preparation of Nano-Structured Polyaniline Composite Film via “Carbon Nanotubes Seeding” Approach and its Gas-Response Studies

Preparation, modification, morphology tailor and application of conjugated conductive polymer in chemical sensors

Gas Sensing Properties of A Composite Composed of Electrospun Poly(Methyl Methacrylate) Nanofibers and in Situ Polymerized Polyaniline

Preparation and Characterization of Polyaniline/Mmt Conductive Composites

Preparation Of A Nanowire-Structured Polyaniline Composite And Gas Sensitivity Studies

O2 plasma-functionalized SWCNTs and PEDOT/PSS composite film assembled by dielectrophoresis for ultrasensitive trimethylamine gas sensor.

High Performance Gas Sensors Based on In-Situ Fabricated ZnO/polyaniline Nanocomposite: the Effect of Morphology on the Sensing Properties

Gas sensing behavior of polyvinylpyrrolidone-modified ZnO nanoparticles for trimethylamine

Gas sensitivity of a composite of multi-walled carbon nanotubes and polypyrrole prepared by vapor phase polymerization

Fabrication of Polypyrrole Composite Film Based Trimethylamine Sensor Via Simple Method

Composites of Fe2O3 Nanosheets with Polyaniline: Preparation, Gas Sensing Properties and Sensing Mechanism

Fabrication and gas sensitivity of polyaniline–titanium dioxide nanocomposite thin film

[Low-Concentration CO₂ Adsorption on Polyaniline/Zeolite Y Composites].

Fabrication and design of a toxic gas sensor based on polyaniline/titanium dioxide nanocomposite film by layer-by-layer self-assembly

Fabrication and Ammonia Gas Sensing of Palladium/polypyrrole Nanocomposite

Preparation of Water Soluble Poly(Aniline) and Its Gas-Sensitivity

Preparation of Polythiophene Composite Film by in Situ Polymerization at Room Temperature and Its Gas Response Studies