Abstract:The conductive nano-Al/polyaniline composites were prepared by the milling method in the solid state. Here, aluminum nanostructures were prepared in two different mechanical methods, wire drawing and wire milling in the presence of lubricant oil. The effects of the preparation methods on the structures and morphologies of aluminum nanostructures were investigated by XRD and FESEM. The results show that the shape and size of aluminum nanoparticles in the preparation by the wire drawing method are significantly different than the wire milling method. The aluminum nanostructures were prepared by milling method have flake-like nanosheets while the wire drawing method leads to the formation of spherical ultrafine nanoparticles, which particles size are in the range of 30–60 nm. Then, polyaniline was produced using a solid-state polymerization process by the chemical reaction between aniline hydrochloride and potassium peroxydisulfate. Finally, nano-Al/polyaniline composites were prepared by mechanical milling at room temperature. The quantitative analysis was carried out with the materials analysis using diffraction (MAUD) method and weight fraction for aluminum and PANI were calculated 6.66% and 93.34%, respectively. Electrical conductivity measurements show the conductivity (1.2 × 10 −2 S cm −1 at 25 °C) for polyaniline emeraldine salt and (1.02 × 10 −3 S cm −1 at 25 °C) in nanocomposite respectively. The results show that by adding aluminum nanoparticles to the polymer the conductivity of nanocomposite (Al/PANI-ES) is lower than that for pure (PANI-ES). Thermogravimetry and differential thermal analysis curves show pure (PANI-ES) and nanocomposite (Al/PANI-ES) have a similar thermal degradation process. The total weight loss in TG curve of pure PANI-ES, in the temperature range 45–800 °C is 46.28% but, total weight loss observed in nanocomposite is 38.67%. Therefore, nanocomposite has higher thermal stability than that of the pure PANI-ES.

Polyaniline/iron nanocomposites prepared by cryomilling

Electromagnetic Nanocomposites Prepared by Cryomilling of Polyaniline and Fe Nanoparticles

Preparation and Magnetic Properties of ZnCuCrLa Ferrite and Its Nanocomposites with Polyaniline

Novel polyaniline-LiNi0.5La0.02Fe1.98O4 nanocomposites prepared via an in situ polymerization

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

Synthesis and ferrimagnetic properties of novel Sm-substituted LiNi ferrite–polyaniline nanocomposite

Preparation and Characterization of Polyaniline/Mmt Conductive Composites

Abs/Iron Nanocomposites Prepared by Cryomilling

Conductive nano-Al/polyaniline composites prepared via mechanical milling

Rod-shaped polyaniline-barium ferrite nanocomposite: preparation, characterization and properties.

Composition dependent magnetic properties of iron oxide - polyaniline nanoclusters

Preparation and electromagnetic properties of Polyaniline(polypyrrole)- BaFe 12O 19/Ni 0.8Zn 0.2Fe 2O 4 ferrite nanocomposites

Highly dispersed crystalline magnetic and conductive polyaniline/iron oxide nanocomposite films

Preparation,Characterization and Properties of Polyaniline-barium Ferrite Nanocomposite

Fabrication, characterization, spectroscopic, and magnetic properties of polyaniline/magnetite (PANi/Fe3O4) nanocomposites

Polyaniline Stabilized Magnetite Nanoparticle Reinforced Epoxy Nanocomposites

Synthesis And Electro-Magnetic Properties Of Polyaniline-Barium Ferrite Nanocomposite

Magnetoresistive Polyaniline-Magnetite Nanocomposites with Negative Dielectrical Properties

PET/SiO2 Nanocomposites Prepared by Cryomilling

Microstructure and magnetic properties of nanocomposite Nd2Fe14B/α-Fe magnetic material prepared by mechanical milling

A novel mechanochemical synthesis of ferromagnetic Fe3Al nanoparticles and preparation of its polyaniline nanocomposite