Abstract:This article presents a series of nanocomposites of a polyester [poly(ethylene terephathalate), PET] with different contents of layered silicates of montmorillonite (MMt) by a controlled process, that is, controlling the way to pretreat MMt, the content of MMt, the kind of reagents used, and the way for MMt to be added. Also investigated, in detail, were the properties, nanostructure, and distribution of nanocomposites with an MMt content below 5% by weight. Results by TEM and AFM showed that the nanoparticles are in a normal distribution with a most probable size of 30-70 nm; the exfoliated MAR lamellae interacting with the PET molecular chain produced more regular chain patterns than did pure PET itself when the MMt content was low (lower than 3% by weight); and the agglomerated particles seem not to be found in an MMt content less than 3% by weight, but to increase with the MMt content in the nanocomposites. The investigation of these nanocomposite properties showed that the optimized properties require an optimized MMt content within 2-3% by weight. When MAR is increased from 3 to 5% by weight in the nanocomposites, agglomeration is unavoidable. Thus, the critical content for MMt added to PET is about 3%, by weight. X-ray results showed the appearance of several small diffraction peaks in the 2theta angle from 1degrees to 7degrees for the annealing nanocomposite samples; these peaks are thought to be from the residue of unexfoliated MMt lamellae or metastable (unstable) MMt lamellae. DSC results proved that the nanocomposites have a higher crystallization rate than that of pure PET due to an exfoliated MMt lamellae nucleation effect. Thus, to obtain a stable nanostructure (or nanocomposite), the MMt content needs to be controlled. The nanostructure plays such a role in the crystallization nucleation of nanocomposites. The interaction of exfoliated lamellae with the molecular chain causes a more regular chain pattern and affects the PET crystallization rate and morphology. (C) 2002 Wiley Periodicals, Inc.

PET/SiO2 Nanocomposites Prepared by Cryomilling

Thermal behaviors of poly(ethylene terephthalate)/SiO2 nanocomposites prepared by cryomilling

KINETICS OF ISOTHERMAL CRYSTALLIZATION FOR PET/MONTMORILLONITE NANOCOMPOSITES

Structural changes in poly(ethylene terephthalate) induced by cryomilling and ambimilling

Crystallization and Morphology of PET/SiO2 Nanocomposites

Effect of Cryomilling on the Thermal Behaviors of Poly(ethylene Terephthalate)

Preparation and characterization of PET/silica nanocomposites

Preparation of In-Situ Polymerized Inorganic Particles/PET Speciality Compounds and Modification on Them

Preparation and Crystalline Properties of PET/ZnO Nano-meter Composite

The Melting Behavior of Poly(Ethylene Terephthalate)/SiO2 Nanocomposites

Abs/Iron Nanocomposites Prepared by Cryomilling

Isothermal Crystallization and Subsequent Melting Behavior of Poly(Ethylene Terephthalate)/Silica Nanocomposites

The Melting and Recrystallization Behavior of Poly(ethylene Terephthalate)/SiO<sub>2</sub> Nanocomposites Studied by Step-Scan DSC

Enhanced crystallization and properties of poly(ethylene terephthalate) nanocomposites with zeolites from 3D to 2D topologies

Inhibited transesterification of poly(butylene terephthalate)/poly(ethylene terephthalate)/SiO2 nanocomposites by two processing methods

Investigation of Properties, Nanostructure, and Distribution in Controlled Polyester Polymerization with Layered Silicate

In situ synthesis of poly(ethylene terephthalate- co -isophthalate)–SiO 2 nanocomposites and their optical properties

Microstructure and Mechanical Properties of SiC/zirconia-toughened Mullite Nanocomposites Prepared from Mixtures of Mullite Gel, 2Y-TZP, and SiC Nanopowders

MECHANICAL PROPERTIES OF POLYIMIDE COMPOSITES FILLED WITH SiO2 NANO-PARTICLES AT ROOM AND CRYOGENIC TEMPERATURES

Fabrication of Nano-Sic_p/al Composite by High Energy Ball Milling

Study of the Preparation and Properties of Pbt/Epoxy/Sio2 Nanocomposites