Abstract:C/C materials represent as materials with specific performance, therefore they are applied in various industries. It is essential to figure out the paths to predict, to provide and to enhance their properties to obtain high performance products. It is well known that strong matrix/reinforcer adhesion provides better strength utilization and therefore better properties for the majority of composite materials of all types (Heim in Compos Part B Eng 54:365–370, 2013), (Hancock and Cuthbertson in J Mater Sci 5:762–768, 1970), (Yang et al. in Polymers 13:2764, 2021). However some researchers note that strong adhesion in the materials that are exposed to high temperatures leads to cracking and significant properties degradation (Vignoles et al. in The Control of interphases in carbon and ceramic matrix composites, Wiley, Hoboken, 2012), (Zhang et al. in Compos Struct 340, 2024). In this work, the effect of the pyrocarbon layer applied on the surface of carbon fibers used for reinforcement of formaldehyde novolac resin based carbon/carbon (C/C) material prepregs was investigated. For the first time we used this effect to prove that lower matrix/reinforcer adhesion in C/C materials prepregs leads to better material behavior during pyrolysis, which results in higher mechanical properties of the pyrolised samples in comparison with the samples demonstrating stronger matrix/reinforcer adhesion. The prepregs were thermally treated at various temperatures, the physical and mechanical performance evolution of the prepregs at different carbonization stages were analyzed. Comparative study of the features of the prepregs with pyrocarbon coated and uncoated carbon fiber as a reinforcement were carried out. The damping effect of the pyrocarbon on the fiber surface were advertised, allowing to mitigate the carbonization-caused effects. The prepregs reinforced with pyrocarbon-modified carbon fibers demonstrated lower cracking performance and higher mechanical performance comparing with the uncoated fiber reinforced prepregs.

Influence of Precursors on Preparation of C/C Composites by CVI

Preparation of C/C Composites by Thermal Gradient Chemical Vapor Infiltration with Vaporized Kerosene As a Precursor

Densification Behavior and Performances of C/C Composites Derived from Various Carbon Matrix Precursors

The effect of carbon nanotubes on the microstructure and morphology of pyrolytic carbon matrices of C–C composites obtained by CVI

Properties of Carbon Nano-Tubes–cf/sic Composite by Precursor Infiltration and Pyrolysis Process

Effect of chemical vapor infiltration on the flexural properties of C/C-SiC composites prepared by the precursor infiltration pyrolysis method

Micro- and nano-structural investigations of C/C composites

Progress in Catalytic Preparation of Carbon/Carbon Composites

Research on Structures and Properties of C/C Composites Using the Preparation of HCVI

PROGRESS OF RESEARCH ON PREPARATION OF CARBON/CARBON COMPOSITE MATERIAL BY THE CHEMICAL LIQUID VAPOR INFILTRATION METHOD

Microstructures and properties of C/C–SiC composites derived from different gaseous carbon matrix precursors

Process Optimization of C/C Composites Fabrication with Multi-physics Fields CVI

Effect of carbon fiber preform with variable density on the oxidation behavior of C/C composites

Study on C/C composites modified by in-situ vapor-grown carbon nanofibers

Influence of Preparation Method on Property of ACS/Sb2O3 Composite

Influence of precursor content on the microstructure and ablative resistance of CLVD-C/C-SiC-ZrC composites

Effect of Pyrocarbon Content in C/C Preforms on Microstructure and Mechanical Properties of the C/C–SiC Composites

Mechanical and thermal conduction properties of carbon/carbon composites with different carbon matrix microstructures

Improvement of Chemical Liquid Vaporized Infiltration Process for Fast Densification of Carbon/Carbon Composites

Microstructure of the pyrocarbon in aligned carbon nanotube/carbon composites

Reinforcement of C/C materials prepregs with pyrocarbon coated carbon fiber as the way to improve the prepregs properties after pyrolysis