Abstract:Drying is a very important unit operation in many industries such as food, pharmaceuticals, chemicals and ceramics. In most cases, wet materials are dried by forced convection using hot air flow. Heat and mass transfer processes during drying have been studied by both experimental and numerical simulation methods. For the purpose of studying the mechanism of heat and mass transfer and stress-strain distribution during the hot air drying of biological porous medium, two-way coupled thermo-hydro-mechanical mathematical model has been developed to simulate the hot air convective drying process of biological porous media on basis of Fickian diffusion theory, Fourier’s law of heat conduction and thermoelasticity mechanics. The following assumptions were made in order to find a solution to the hot air drying model: the biological porous medium was homogeneous and isotropic; the deformation during drying was elastic. The transient model, composed of a system of partial differential equations, was solved by finite difference methods. The computational procedure was programmed using C language. Some physical and mechanical properties of carrot changing with dry basis moisture content and temperature were considered. The numerical results were compared with available experimental data obtained during the drying of potatoes and carrots. The relative errors between numerical results and experimental data were both less than 5%, which showed the numerical results obtained using the mathematical model were in good agreement with the experimental data. Numerical simulations of the drying curve variations and the spatio-temporal distributions of moisture, temperature and drying stresses and strains of carrot were also evaluated. The temperature and moisture content showed a gradient inside carrot slice during drying. As the drying process proceeded, the temperature inside the carrot slice initially increased to reach the wet bulb temperature of the environment and eventually leveled off. The dry basis moisture content inside the carrot slice decreased, with the fastest decreased at the heat and mass transfer interface, eventually reached the equilibrium moisture content of the potato and leveling off. Both the moisture content gradient and the temperature gradient decreased gradually in the thickness direction. The normal stress was negative in all parts of the carrot slice, and the larger the closer to the evaporation interface. The shear stress was positive in all parts of the carrot slice, and the maximum shear stress occurred in the middle of the carrot slice. As in the case of the normal stress, the values of the normal strain were negative. The change trend of normal strain with time was consistent with that of moisture content. These results indicated that the observed physical deformations were caused by the dehydration of carrot slice during drying. The influence of drying conditions, such as air temperature, air velocity and the thickness of porous media on drying process was analyzed. Analysis showed that under certain drying conditions, the higher air temperature, the greater air velocity and the thinner slice thickness, the shorter drying time. This work should help in developing an understanding of the relationship between mass and heat transfer, shrinkage, stress, strains and physical degradation.

Simulation and Analysis of Drying Conditions for Rotary Dryer

Optimal Design of an Angular Box for a Mixed Flow Grain Dryer

Performance Simulation of a Modified Geothermal Grain Dryer Based at Menengai Well 3 in Kenya

The simulation analysis and experiment of drying thin-layer radish strips

SIMULATION OF BIOMASS DRYING IN A DIRECT CONTACT ROTARY DRYER

Analysis and structure optimization of the flow and temperature fields of the large-scale hot air drying room

DESIGN AND EXPERIMENTAL VERIFICATION OF SELF-PRIMING HOT AIR TEMPERATURE CHANGING DEVICE FOR GRAIN DRYER

Heat-fluid-solid coupling heat transfer analysis and parameter optimization in walnut drying device based on finite element method

Study on Numerical Simulation of Airflow Distribution in Hot Pump Drying Room of Peppercorns

Exergy analysis and optimisation of an industrial-scale circulation counter-flow paddy drying process

Numerical study of heat and mass transfer during drying process of barley grain piles based on the pore scale

Experimental Investigation on a Solar Assisted Heat Pump In-Store Drying System

Theoretical and experimental research on heat and mass transfer in a turbine thin layer dryer

Mathematical Model and Numerical Simulation of Biological Porous Medium During Hot Air Drying

Research on key technologies of finite element flow field in airflow drying process analysis

Flow field analysis and design optimisation of Tibetan medicine double heat pump drying room

The Experimental Research of Aromatic Hydrocarbon Sinter Drying

Performance Optimization and Numerical Simulation Study of Sludge Low-Temperature Drying System

Forecast Analyzing on Thin Layer Drying of Radish Strip and Experiment

Simulation of Heat and Mass Transfer of Cut Tobacco in a Batch Rotary Dryer by Multi-Objective Optimization

Drying kinetic, quality, energy and exergy performance of hot air-rotary drum drying of green peas using adaptive neuro-fuzzy inference system