Abstract:The 6××× series aluminum alloys Al-Mg-Si-Cu are widely used in the transportation and building industries due to their comprehensive mechanical properties, adequate formability, high corrosion resistance and good weldability. For decades, ultrafine grain structure (UFG) produced by severe plastic deformation (SPD) has been proved to be a promising way in strengthening Al alloy materials. Although this method can guarantee a great improvement in strength, the obtained ductility is always disappointing. Besides, this method has a limitation to fabricate products suitable for practical use. Recently, combining deformation and aging has been proposed to pro-duce high-strength Al alloys. This strategy is very effective in achieving Al alloys with strength-ductility synergy even through conventional producing process, for example, rolling and aging. The strain ratio of deformation is crit-ical in tuning the mechanical properties which could be acquired by the above method. The effect of deformation strain ratio on the age-hardening behaviors and microstructure in Al-Mg-Si-Cu alloy produced by combining cold-rolling and aging are investigated using hardness test, tensile test, EBSD and TEM in this work. The results show that the as-rolled hardness increases gradually with deformation strain ratio. The age-hardening potential declines with the increase of strain ratio, though post-aging could further strengthen the as-rolled alloys. The grains elongate along the rolling direction during deformation and finally have a lamellar structure. Fragmentation and extensive defects like sub-grain boundaries occurs inside the grains. The dislocations become denser inside the alloy with the increase of the deformation ratio. When the deformation ratio is large (above 60%), formation of dislocation tan-gling and sub-grains are observed. Deformation-induced change of the dislocation configuration affects the precipitation significantly. Due to the interaction between solutes precipitation and defects annihilation, the distribution of precipitates undergoes a change from being isolated to a continuous manner.

Development of Deforming and Aging Cu-Cr Alloy

Reforming Nanostructured CuAg Alloy to Improve Ductility and Electrical Conductivity

Managing Mechanical and Electrical Properties of Nanostructured Cu-Fe Composite by Aging Treatment

Research Development of Rapidly Solidified Cu-Cr Alloys

Ageing Behavior of Cu-15Ni-8Sn Alloy Prepared by Mechanical Alloying

Microstructure and Electrical Properties Evolution of Cu-3 ％ Cr During Aging

Effect of deformation and aging treatment on the microstructure and properties of Cu-0.45Cr-0.14Ti (wt.%) alloy

EFFECT OF HEAVILY DRAWING ON THE MICROSTRUCTURE AND PROPERTIES OF Cu-Cr ALLOYS

Mechanical deformation and properties of CuCr25 alloy

Microstructure and Properties of Cold Drawing Cu-2.5% Fe-0.2% Cr and Cu-6% Fe Alloys

Application and Research Status of Zn-Cu-Ti Alloy

Deformation Microstructure and Property Control of CuCrZr Alloy Directionally Solidified at Room Temperature C-ECAP

Study of Deformation and Aging Behaviors of a Hot Rolled–quenched Cu–Cr–Zr–Mg–Si Alloy During Thermomechanical Treatments

Influences of Cold Rolling and Aging on Microstructure and Property of CuCrSn Alloy

Aging Property of Cu-Ag-Zr Alloy

Effect of Aging Treatment on Microhardness and Electrical Conductivity of Extruded CuCr25 Alloy

Optimizing strength and electrical conductivity of Cu-Cr-Zr alloy by two-stage aging treatment

Prospect and Current Status of Research on Cu-Ag Alloys with High Strength and Conductivity

Microstructures and Mechanical Properties of Al-Zn-Mg-Cu Alloys under Multi-Directional Severe Strain and Aging

EFFECT OF PRE-DEFORMATION ON AGE- HARDENING AND MICROSTRUCTURE IN Al-Mg-Si-Cu ALLOY

Microstructure and properties of Cu-Cr-Zr (Mg) alloys subjected to cryorolling and aging treatment