Abstract:In this research, the cast-homogenized Mg-9Gd-3Y (GW93) alloy was subjected to isothermal hot compression tests at different temperatures ranging from 300 to 450 °C and different strain rates from 0.001 to 1 s -1 , and its hot compression deformation characteristic was studied. With the aid of the dynamic material model and the Murty instability criterion, a 3-dimensional (3D) hot processing map describing the intrinsic processability of the material was established. Through the secondary development, the 3D hot processing map of GW93 alloy was then imported into the finite element software DEFORM-3D, implementing backward extrusion forming simulation of thin-walled tubes under various process parameters. The power dissipation coefficient was utilized to evaluate the material's formability after the deformation. The effects of deformation temperature and extrusion speed on the formability of thin-walled tubes were studied, and the process parameters were optimized to 430 °C and 0.25 mm/s. Afterward, the thin-walled tubes with an outer diameter of 40 mm, wall thickness of 2 mm and height of 50 mm were prepared by practical backward extrusion experiments under 3 different groups of parameters. The present study suggests that under the parameters of 430 °C and 0.25 mm/s, the thin-walled tube was granted with an intact appearance and undergo a secure deformation. Furthermore, its microstructure was characterized by the presence of fine recrystallized grains. The surfaces of the thin-walled tubes would be prone to cracking under the other 2 groups of parameters (430 °C/0.1 mm/s and 410 °C/0.25 mm/s), with clearly visible cracks observed under an optical microscope.

Extrusion swell behavior of tube compound

The polymer melt swelling behavior in micro-extrusion process for preparation of continuous carbon fiber reinforced PP prepreg filament

Plasticity Improvement of Ball-Spun Magnesium Alloy Tube Based on Stress Triaxiality

Study on the Melt Rheological Characterization of Micro-Tube Gas-Assisted Extrusion Based on the Cross-Scale Viscoelastic Model

Melt extrudate swell behavior of multi‐walled carbon nanotubes filled‐polypropylene composites

Tubing Extrusion of a Fluoropolymer Melt

Effect of Strain State on the Surface Roughening for Hydroforming of Aluminum Alloy Tube Based on Cross-Scale Numerical Modeling

Comparative analysis of flow factors and crystallinity in conventional extrusion and gas-assisted extrusion

Two-relaxation-time lattice Boltzmann model of the velocity profiles and volumetric flow rate of generalized Newtonian fluids in a single-screw extruder

Temperature rises and constitutive equation of homogenized 6063 aluminum alloy for extrusion

Effect of Pressure Difference between Inner and Outer Gas Layer on Micro-Tube Deformation during Gas-Assisted Extrusion

Influence of mechanical properties of tube on forming limits and deformation characteristics in expansion drawing process

Effect of Mold Flow Channel Parameters on Gas-Assisted Extrusion of Medical Microtubules

Process fundamentals and quality investigation in extrusion 3D printing of shear thinning materials: extrusion process based on Nishihara model

Behaviour of Tube under Axial Crush Load with Considering Effect of Heat Exchanged

Optimization of numerical parameters and microstructure evolution on 2195 Al–Li alloy extrusion process

High temperature flow behavior and constitutive model of alloy transition layer in composite steel tube prepared by centrifugal self‐propagating high‐temperature synthesis (SHS)

Effect of Oligomer Addition on Tube Dilation in Polymer Nanocomposite Melts

Effects of Temperature Distribution on Microstructure and Mechanical Properties of Hot Extruded Al–Zn–Mg–Cu Alloy Pipe with Variable Cross-Section

Optimization of Hot Backward Extrusion Process Parameters for Thin-Walled Tubes of Mg-9Gd-3Y Alloy Based on 3D Processing Maps

Influence of process parameters on the flow forming quality of thin-walled tube with large diameter-thickness ratio