Abstract:Drying is a very important unit operation in many industries such as food, pharmaceuticals, chemicals and ceramics. In most cases, wet materials are dried by forced convection using hot air flow. Heat and mass transfer processes during drying have been studied by both experimental and numerical simulation methods. For the purpose of studying the mechanism of heat and mass transfer and stress-strain distribution during the hot air drying of biological porous medium, two-way coupled thermo-hydro-mechanical mathematical model has been developed to simulate the hot air convective drying process of biological porous media on basis of Fickian diffusion theory, Fourier’s law of heat conduction and thermoelasticity mechanics. The following assumptions were made in order to find a solution to the hot air drying model: the biological porous medium was homogeneous and isotropic; the deformation during drying was elastic. The transient model, composed of a system of partial differential equations, was solved by finite difference methods. The computational procedure was programmed using C language. Some physical and mechanical properties of carrot changing with dry basis moisture content and temperature were considered. The numerical results were compared with available experimental data obtained during the drying of potatoes and carrots. The relative errors between numerical results and experimental data were both less than 5%, which showed the numerical results obtained using the mathematical model were in good agreement with the experimental data. Numerical simulations of the drying curve variations and the spatio-temporal distributions of moisture, temperature and drying stresses and strains of carrot were also evaluated. The temperature and moisture content showed a gradient inside carrot slice during drying. As the drying process proceeded, the temperature inside the carrot slice initially increased to reach the wet bulb temperature of the environment and eventually leveled off. The dry basis moisture content inside the carrot slice decreased, with the fastest decreased at the heat and mass transfer interface, eventually reached the equilibrium moisture content of the potato and leveling off. Both the moisture content gradient and the temperature gradient decreased gradually in the thickness direction. The normal stress was negative in all parts of the carrot slice, and the larger the closer to the evaporation interface. The shear stress was positive in all parts of the carrot slice, and the maximum shear stress occurred in the middle of the carrot slice. As in the case of the normal stress, the values of the normal strain were negative. The change trend of normal strain with time was consistent with that of moisture content. These results indicated that the observed physical deformations were caused by the dehydration of carrot slice during drying. The influence of drying conditions, such as air temperature, air velocity and the thickness of porous media on drying process was analyzed. Analysis showed that under certain drying conditions, the higher air temperature, the greater air velocity and the thinner slice thickness, the shorter drying time. This work should help in developing an understanding of the relationship between mass and heat transfer, shrinkage, stress, strains and physical degradation.

Optimization of Drying Process for Multilayer Belt Dryer

Numerical Simulation and Optimization of a Multilayer Belt Dryer for Granular Food Materials

Simulation of drying process for 5HCCX-1.6 multi-zone belt dryer

Modeling of Muti-layer Far-Infrared Dryer

Mass-Transfer Simulation Software Study of Sliced Porous Production During Convection Drying Process

A fully coupled multiphase model for infrared-convective drying of sweet potato

Analysis of Air Velocity Distribution in a Multilayer Conveyor Dryer by Computational Fluid Dynamics

The simulation analysis and experiment of drying thin-layer radish strips

Modeling Simultaneous Heat and Mass Transfer for Microwave Drying on Apple

Heat-transfer simulation of slice potato during drying.

Mathematical Model and Numerical Simulation of Biological Porous Medium During Hot Air Drying

Modeling and simulation of drying characteristics on flexible filamentous particles in rotary dryers

The Influence of Feedstock Stacking Shape on the Drying Performance of Conveyor Belt Dryer

A novel mechanical vapor compression vacuum belt drying system: Model development, experimental verification and performance prediction

Experimental investigation and thin-layer modelling of cassava slice drying

Simulation of Countercurrent Multi-Effect Drying System

SIMULATION AND OPTIMIZATION OF CROSS FLOW GRAIN DRYERS

Pore Network Model and Simulation of Transport Process for Grain Drying

Simulation and Experimental Analysis of Mass Transfer in Drying a Single Corn Kernel

Study on heat and mass transfer of flexible filamentous particles in a rotary dryer

Mathematical Modeling of Moisture and Heat Transfer in Wood Particles During Convective Drying.