Abstract:The adsorption capacities of ion exchangers with the primary amine (Lewatit® VP OC 1065) and polyamine (DiaionTM CR20) functional groups relative to Pd(II) and Cu(II) ions were tested in a batch system, taking into account the influence of the acid concentration (HCl: 0.1–6 mol/L; HCl-HNO3: 0.9–0.1 mol/L HCl—0.1–0.9 mol/L HNO3), phase contact time (1–240 min), initial concentration (10–1000 mg/L), agitation speed (120–180 rpm), bead size (0.385–1.2 mm), and temperature (293–333 K), as well as in a column system where the variable operating parameters were HCl and HNO3 concentrations. There were used the pseudo-first order, pseudo-second order, and intraparticle diffusion models to describe the kinetic studies and the Langmuir and Freundlich isotherm models to describe the equilibrium data to obtain better knowledge about the adsorption mechanism. The physicochemical properties of the ion exchangers were characterized by the nitrogen adsorption/desorption analyses, CHNS analysis, Fourier transform infrared spectroscopy, the sieve analysis, and points of zero charge measurements. As it was found, Lewatit® VP OC 1065 exhibited a better ability to remove Pd(II) than DiaionTM CR20, and the adsorption ability series for heavy metals was as follows: Pd(II) >> Zn(II) ≈ Ni(II) >> Cu(II). The optimal experimental conditions for Pd(II) sorption were 0.1 mol/L HCl, agitation speed 180 rpm, temperature 293 K, and bead size fraction 0.43 mm ≤ f3 < 0.6 mm for DiaionTM CR20 and 0.315–1.25 mm for Lewatit® VP OC 1065. The maximum adsorption capacities were 289.68 mg/g for Lewatit® VP OC 1065 and 208.20 mg/g for DiaionTM CR20. The greatest adsorption ability of Lewatit® VP OC 1065 for Pd(II) was also demonstrated in the column studies. The working ion exchange in the 0.1 mol/L HCl system was 0.1050 g/mL, much higher compared to DiaionTM CR20 (0.0545 g/mL). The best desorption yields of %D1 = 23.77% for DiaionTM CR20 and 33.57% for Lewatit® VP OC 1065 were obtained using the 2 mol/L NH3·H2O solution.

Adsorption of Molybdenum from Chlorination Leaching Solution of Ni-Mo Ore by Ion-Exchange

Properties and Mechanism of Molybdenum and Zirconium Adsorption by a Macroporous Silica‐Based Extraction Resin in the MAREC Process

Selective Adsorption of Molybdenum Ions on Ionic Liquid-Loaded Resin Containing 1-Butyl-3-methylimidazolium(2,4,6-trimethyl)benzodithioate

Solvent Extraction of Molybdenum (VI) from Hydrochloric Acid Leach Solutions using P507. Part II: Stripping and Mechanism

Molybdenum Separation from Sodium-Tungstate-Molybdenum Aqueous Solutions Using an Anionic Gel-Based 201 × 7 Resin

Targeted elimination of molybdenum ions from a leaching solution with the ability of radiated grafting GMA-PAN nanofibers

Solvent Extraction of Molybdenum (VI) from Hydrochloric Acid Leach Solutions Using P507. Part I: Extraction and Mechanism

Effects and mechanisms of ternary solution of NaOH-Na2CO3-Na2SO4 on the recovery of molybdenum from residues containing multiple molybdates

Extraction kinetics of separating molybdenum(VI) over iron(III) from high acid leach solutions with mixtures of P507 and N235

Research on removal of iron and copper from low-grade molybdenum calcine in strong acid system

Removal of Thorium and Uranium from Aqueous Solution by Adsorption on Hydrated Manganese Dioxide

Highly enhanced selectivity for the separation of rhenium and molybdenum using amino-functionalized magnetic Cu-ferrites

Preparation of Manganese Oxide-Cation Exchange Resin Hybrid Material and Its Adsorption Property for Heavy Metals in Aqueous Solution

Study on the efficiency of manganese oxide-bearing manganese sand for removing Mn2+ from aqueous solution

Crosslinked Polydiallyldimethylammonium Chloride Adsorbent for the Selective Separation of Rhenium Ions from Pregnant Leach Solutions

A Millimeter-Sized Negatively Charged Polymer Embedded with Molybdenum Disulfide Nanosheets for Efficient Removal of Pb(II) from Aqueous Solution

Efficient and Rapid Removal of Nickel Ions from Electroplating Wastewater Using Micro-/Nanostructured Biogenic Manganese Oxide Composite

Comparative adsorption of heavy metal ions in wastewater on monolayer molybdenum disulfide

Selective Adsorption of Lead (ii) Ions by A Manganese Dioxides-Loaded Adsorption Resin

Evaluation of Adsorption Ability of Lewatit® VP OC 1065 and DiaionTM CR20 Ion Exchangers for Heavy Metals with Particular Consideration of Palladium(II) and Copper(II)

Enhanced Removal of Nickel(ii) from Water by Utilizing Gel-Type Nanocomposite Containing Sub-5 Nm Hydrated Manganese(iv) Oxides