Abstract:Nylon 6 and its blends with a polyamide block copolymer were prepared by solvent blending and co-precipitation process.The samples were melted at 260℃ and then cooled at a rate of 30 K/min to obtain the controlled cooling samples(CCS).Investigations were carried out on the influence of thermal treatment on crystal melting behavior and crystal structure of nylon 6 and the blends by differential scanning calorimetry (DSC),wide-angle X-ray diffraction(WAXD)and polarized optical microscopy(POM).Measurements were taken after annealing at 190℃ with varied time from O h to 48 h.The resuhs indicated that the existing of the polyamide block copolymer affected the crystal behavior and the crystal structure of nylon 6,comparing to those of pure nylon 6 under the same thermal conditions.The pure nylon 6 tends to form α crystals,but it in the blends forms γ crystals.It was also found that annealing treatment had different effects on these two kinds of samples.For Nylon 6,annealing treatment only promoted the transformation of nylon 6 from amorphous to crystal phase,improved the crystalline structure and increased the crystal degree greatly without crystal form change.The crystal degree increased by about 61% after annealing for 48 h.For the blends.annealing treatment not only promoted the transformation from amorphous to crystal phase,improved the γ form crystalline structure and increased the crystal degree,but also resulted in the formation new α crystals.Compared with the original sample,the crystal degree increased by about 84%after annealing for 48 h.

Non-isothermal Crystallization Behavior of PA6 in PA6/POE

Crystallization Behavior of Miscible PA6 and PA6IcoT Blends

Crystallization Behavior of Reactive Blends Between Pbs and Pa6icot

Non-isothermal crystallization behavior of polyamide 6 under confined condition

Facile characterization of isothermal crystallization and microphase separation kinetics of polyamide 6 (PA6)‐based thermoplastic elastomers

Non-isothermal Crystallization Kinetics of Polypropylene/Polyamide 6 Blends In-situ Compatibilized with PAG

Mechanical Properties and Nonisothermal Crystallization Kinetics of Polyamide 6/functionalized TiO2nanocomposites

Isothermal crystallization kinetics and melting behavior of poe-g-mah compatibilized PA11/POE blends

INFLUENCE OF THERMAL TREATMENT ON CRYSTAL MELTING BEHAVIOR AND CRYSTAL STRUCTURE OF NYLON 6 AND POLYAMIDE BLOCK COPOLYMER/NYLON 6 BLENDS

Crystallization behavior of reactive blend of poly(butylene succinate) and amorphous nylon poly(hexamethylene iso-co-tere)phthamide)

Phase stability and melting behavior of the α and γ phases of nylon 6

Research on Recycled PET/PA6 Blend

Effect of Thermal Oxidative Aging on the Crystallization Behavior and Properties of Nylon-6

Facile synthesis of polyamide 6 (PA6)-based thermoplastic elastomers with a well-defined microphase separation structure by melt polymerization

A New Method to Prepare Low Melting Point Polyamide‐6 and Study Crystallization Behavior of Polyamide‐6/calcium Chloride Complex by Rheological Method

Influence of TLCPa on miscibility and crystallization behavior of PA 6/PA 66 blends

Study on Crystal Behavior of PA-66 with Thermotropic Liquid Crystalline Copolyester

Toughening Behavior and Morphology Study of PA6/thermal Liquid Crystalline Polyamide Blends

Mutual Nucleating and Crystallization Behavior of Poly (ethylene Terephthalate)/polyamide 66 Blends

Crystallization behavior of polyamide 6/halloysite nanotubes nanocomposites

Study on the Thermal Stability of PA6 Fibers