Abstract:This research aims at increasing the utilization of platinum-ruthenium alloy (Pt-Ru) catalysts and thus lowering the catalyst loading in anodes for methanol electrooxidation. The direct methanol fuel cell’s (DMFC) anodic catalysts, Pt-Ru/C, were prepared by chemical reduction with a reducing agent added in two kinds of solutions under different circumstances. The reducing agent was added in hot solution with the protection of inert gases or just air, and in cold solution with inert gases. The catalysts were treated at different temperatures. Their performance was tested by cyclic voltammetry and potentiostatic polarization by utilizing their inherent powder microelectrode in 0.5 mol/L CH3OH and 0.5 mol/LH2SO4 solution. The structures and micro-surface images of the catalysts were determined and observed by X-ray diffraction and transmission electron microscopy, respectively. The catalyst prepared in inert gases showed a better catalytic performance for methanol electrooxidation than that prepared in air. It resulted in a more homogeneous distribution of the Pt-Ru alloy in carbon. Its size is small, only about 4.5 nm. The catalytic performance is affected by the order of the reducing agent added. The performance of the catalyst prepared by adding the reductant at constant temperature of the solution is better than that prepared by adding it in the solution at 0°C and then heating it up to the reducing temperature. The structure of the catalyst was modified, and there was an increase in the conversion of ruthenium into the alloyed state and an increase in particle size with the ascension of heat treatment temperature. In addition, the stability of the catalyst was improved after heat treatment.

Phosphomolybdic Acid Modified Platinum Electrode of Methanol Fuel Cell

Catalysis Used to the Direct Methanol Feul Cell Anode

Mitigating Phosphate Anion Poisoning of Cathodic Pt/C Catalysts in Phosphoric Acid Fuel Cells

Preparation and electrocatalytic performance of heteropolyacid modified platinum electrode

Effect of Surface Composition of Electrochemically Codeposited Platinum/Molybdenum Oxide on Methanol Oxidation

Hybrid of Molybdenum Trioxide and Carbon As High Performance Platinum Catalyst Support for Methanol Electrooxidation

Phosphorus Doped MoO2 Enhanced Pt Catalyst for Methanol Oxidation

Preparation and Influence of Performance of Anodic Catalysts for Direct Methanol Fuel Cell

Enhanced Methanol Oxidation Using Polymer-Incorporated Rough Pt Electrodes

Phosphotungstic acid modification boosting the cathode methanol tolerance for high-temperature direct methanol fuel cells

Some Factors Affecting the Performance of Anodic Catalysts for Direct Methanol Fuel Cell

Enhanced Electrocatalytic Performance for Methanol Oxidation with A Magneli Phase Molybdenum Oxide/Pt-Black Composite

Palladium supported on NiFe layered double hydroxide as an effective electrocatalyst for methanol electro-oxidation

Using Phosphomolybdic Acid (h3pmo12o40) to Efficiently Enhance the Electrocatalytic Activity and CO-tolerance of Platinum Nanoparticles Supported on Multi-Walled Carbon Nanotubes Catalyst in Acidic Medium

Phosphate-decorated Pt Nanoparticles as Methanol-tolerant Oxygen Reduction Electrocatalyst for Direct Methanol Fuel Cells

Pore-arrayed hydrogen molybdenum bronze: Preparation and performance as support of platinum nanoparticles for methanol oxidation

Platinum supported on hydroxyl-grafted poly (3,4-ethylenedioxythiophene)-modified RuCo, N-tridoped bamboo-like carbon nanotubes for direct methanol fuel cell

Catalytic Oxidation of Methanol by Aqueous POM on Al2O3 Supported Catalysts and Electrochemical Performance of POM

Enhanced Activity and Durability of Platinum Anode Catalyst by the Modification of Cobalt Phosphide for Direct Methanol Fuel Cells

Enhancing Electrocatalytic Methanol Oxidation on PtCuNi Core–Shell Alloy Structures in Acid Electrolytes

Platinum nanoparticles anchored on aminated silica@PEDOT-PSS hybrid for enhanced methanol oxidation electrocatalysis