Research on sampling method for protective device based on TMS320F2812

PAN XIN,LI YINGCHUN,SUN XINYA,ZHU SHANJUN

DOI: https://doi.org/10.3969/j.issn.1008-0570.2007.05.066

2007-01-01

Abstract:DSPs have been widely used and provide good opportunity for development of microcomputer protective device. This paper compares several sampling algorithms in relay protection sets based on TMS320F2812 and simulations results is presented.

What problem does this paper attempt to address?

Research of Wireless Electrocardiograph Signal Sampling System

Li Luo,Lu Jiangang

DOI: https://doi.org/10.3321/j.issn:1671-4598.2006.12.052

2006-01-01

Abstract:Presents the crucial techniques of hardware and software designing applied to wireless signal sampling device in electrocardiogram monitoring.This type of device is designed with the functions of sampling,filtering,wireless transmitting,and characterized with portable,low-power,anti-interference,intelligent,etc.The system is controlled by MSP430 singlechip.It filters and amplifies the signal and send data wirelessly.Experiments indicate the system is suitable for continuous monitoring.
Design of Experimental Switched Reluctance Drive System Based on DSP

周春,潘再平

DOI: https://doi.org/10.3969/j.issn.1006-7167.2004.04.016

2004-01-01

Abstract:The paper introduced a method to design a small power SRD for experimental teaching by the basic principle of SRD and the characteristics of a serial of DSP——TMS320LF2407. The experimental system can satisfy the request of experiment teaching for SRM.
Study of Turn-on Characteristics of SCRs for ESD Protection with TDR-O and TDR-S TLPs

Ming-xu Huo,Yan Han,You Li,Bo Song

DOI: https://doi.org/10.1109/ipfa.2010.5532309

2010-01-01

Abstract:There are few good evaluation methods to evaluate CDM ESD protection performance such as device turn-on speed, etc. A new current-waveform-based method to evaluate the turn-on speed of an ESD protection device is proposed. The method uses two Transmission-Line Pulse (TLP) Tester to investigate the turn-on characteristics of SCR and related devices. Both intrinsic and normalized turn-on conditions are defined for protection devices to study the different factors that affect the turn-on characteristic under various conditions. The turn-on of both forwardly and reversely working of devices is measured for the CDM model including positive and negative currents. From the experimental results, it is concluded that NMLSCR's performance is superior to PMLSCR in turn-on speed; MLSCR requires higher It1 to be turned on; and the turn-on speed of a PMLSCR decreases significantly with small increases in pulse amplitude under intrinsic working condition while NMLSCR and LSCR do not exhibit such property.
Novel Sampling Algorithm for Dsp Controlled 2 Kw Pfc Converter

JH Zhou,ZY Lu,ZY Lin,YC Ren,ZM Qian,YS Wang

DOI: https://doi.org/10.1109/63.911145

IF: 5.967

2001-01-01

IEEE Transactions on Power Electronics

Abstract:This paper proposed a DSP controlled 2 kW PFC converter with a novel sampling algorithm which can greatly improve switching noise immunity in almost all average current control power supplies. Based on the newly developed DSP chip TMS320F240, a 2 kW PFC stage designed as the front-end of a frequency-variable air-conditioner is implemented. The novel sampling algorithm shows great advantages when the switch operates in the range above 30 kHz.
Hardware Design of ECG Reccording System Based on TMS 320F2812

Bo-sheng HONG,Hang CHEN,Shu-ming YE

DOI: https://doi.org/10.3969/j.issn.1671-7147.2010.03.003

2010-01-01

Abstract:Based on the DSP chip TMS320F2812,the paper designs a portable,high speeding ECG sampling system with QRS detection function,uses on-chip AD to sample ECG signal,ECAN module for CAN bus communication,and transplants the QRS detection algorithm into the chip.The system has small-size and real-time analyzing characteristics.
Research of simulation system of pv on-grid power generation based on dsp

Lu Huifen,Gu Yunjie,Yu Hongibin,Li Wuhua

DOI: https://doi.org/10.3969/j.issn.0254-0096.2013.08.006

2013-01-01

Abstract:TMS320F28027 is used in the system as the control core to simulation the functions of maximum power point tracking (MPPT), frequency and phase synchronization, under voltage and over current protection, automative recovery of under voltage and so on. The topology of the main circuit is the full bridge inversion circuit, which is controlled by the unipolar sinusoidal pulse-width-modulation (SPWM) strategy. MPPT is realized with constant input voltage method. The phase tracking is achieved with software phase lock loop (PLL). The test results show that the system has perfect performance, such as high efficiency, low grid-connected total harmonic distortion (THD), nice tracking performance, consummate over-current protection (OVC) and under-voltage protection (UVP). The relative voltage error is less than 0.7% for MPPT. The relative frequency error is less than 0.09%. The phase error is approximately 2°. The THD of the output voltage is less than 2%. The efficiency of this device is over 84%.
Design of Virtual Device System Based on DSP

刁红泉,张瑶瑶,颜钢锋

DOI: https://doi.org/10.3969/j.issn.1671-7147.2004.01.010

2004-01-01

Abstract:With the development of the computer technology and digital signal processing technology, virtual technology has become popular. Application of virtual technology in control domain is called virtual device. To verify the effect of the controller, on the basis of system model, the virtual device with approximate input-output characteristics is employed for the system's real-time simulation, achieving the aim of reducing on-spot debugging, enhancing controller's security and improving effect. This paper presents hardware and software designs of a virtual device using DSP chip-TMS320F240, TI Com. and verifies the simulation effect of virtual device through application example.
Design Of Comprehensive Motor Protector Based On Improved Sliding-Window Iterative Dft Algorithm

Jinxiang Zhan,Xiaoxiao Cheng,Qunwei Xu,Liang Wu,Guozhu Chen

DOI: https://doi.org/10.1109/ipemc.2016.7512881

2016-01-01

Abstract:This paper introduces a design of comprehensive motor protector based on improved sliding-window iterative discrete fourier transform (DFT) algorithm. It improves the conventional sliding-window iterative DFT, making it easier in calculation and reducing the computation burden of the microprocessor. With electric parameters updating every sampling period, the time response to faults is much improved, compared to the conventional motor protector. For the hardware plan, the protector is controlled by two microcontrollers, one is for the control and measurement module and the other is for the display module. They are connected through RS422 communication. The whole device is compact and layout reasonable, with the advantages of small size and high reliability. The motor protector designed in this paper integrates protection, control, measurement, and communication. Experiment results have verified that it has good performance and high accuracy and can provide comprehensive protection for the motor.
A Novel and Powerful TCAD Methodology to Evaluate Performance of ESD Protection Devices

Yan Han,Shaoyu Ma,Qiang Cui,J.J. Liou,Shurong Dong

DOI: https://doi.org/10.1049/cp:20070677

2007-01-01

Abstract:On-chip electrostatic discharge (ESD) protection requires not only extensive technical experience but also scientific technology computer aided design (TCAD) methodology for evaluation. A novel and powerful TCAD methodology aimed to evaluate performance of ESD protection devices objectively is developed and presented. Mix-mode transient circuit simulation, which depicts ESD events better, is acquired in this simulation method. This TCAD methodology pays more attentions to the transient behaviors and characteristics of ESD protection devices which are more valuable to predict performance of ESD protection devices. This TCAD methodology with good ability of convergence can evaluate the performance of ESD protection devices scientificly and has strong direction ability to the design of ESD protection devices.
Analyse of Protection Devices' Speed Performance against ESD under CDM Using TCAD

Qiang Cui,Shurong Dong,Juin J. Liou,Yan Han

DOI: https://doi.org/10.1109/EDSSC.2007.4450166

2007-01-01

Abstract:Speed performance plays a critical role in protection devices against ESD (Electro-Static Discharge) overstress under CDM (Charged Device Model). It is too demanding to obtain speed performance of protection devices under CDM accurately by testing. Therefore we have to resort to TCAD (Technology Computer Aided Design) method to evaluate speed performance under CDM. This TCAD methodology is based on mix-mode transient circuit simulation, which depicts ESD events better. Two time constants, Ttrigger and Trecover, and two key coefficients, Ftrigger and Crecover, are provided to characterize and evaluate speed performance of ESD protection devices. The results show that this TCAD methodology has a good ability of convergence and is a good tool to evaluate speed performance of ESD protection devices quantificationally. Anlayse results show that speed performance of SCR is superior over ggNMOS in not only triggering but also bypassing ESD currents to recover the voltage towards a safe level.
A smart resampling scheme for digital substation relay protection

Chao Cai,Yuping Lu,Tony Ding,Guofang Zhu

DOI: https://doi.org/10.1109/pes.2010.5589857

2010-07-01

Abstract:The application of IEC61850 and non-conventional instrument transformers (NCIT) brings a new era in the development of substation. The protection intelligent electronic device (IED) in digital substation receives sampled data from different digital data sources (DDS) with digital interface based on IEC 61850–9-2 process bus. The mismatch in sampling rate between protection IED algorithms and different DDSs requires resampling in the protection IED to make sure the protection and other algorithms can run correctly. In this paper, a smart digital resampling scheme based on oversampling interpolator and quasi-continuous interpolator for fully digital relay protection is proposed. A computationally optimal poly-phase implementation structure and nyquist filter for the oversampling interpolator is designed and the Lagrange interpolation algorithm is chosen to approximate the impulse response of the quasi-continuous interpolator considering the reduction in error. Simulation results based on ATP/EMTD and MATLAB demonstrated the effectiveness of the proposed approach.
Fringing Electric Field Sensors for Anti-Attack at System-Level Protection

Xiang Gao,Yiqiang Zhao,Haocheng Ma

DOI: https://doi.org/10.3390/s18093034

IF: 3.9

2018-01-01

Sensors

Abstract:Information system security has been in the spotlight of individuals and governments in recent years. Integrated Circuits (ICs) function as the basic element of communication and information spreading, therefore they have become an important target for attackers. From this perspective, system-level protection to keep chips from being attacked is of vital importance. This paper proposes a novel method based on a fringing electric field (FEF) sensor to detect whether chips are dismantled from a printed circuit board (PCB) as system-level protection. The proposed method overcomes the shortcomings of existing techniques that can be only used in specific fields. After detecting a chip being dismantled from PCB, some protective measures like deleting key data can be implemented to be against attacking. Fringing electric field sensors are analyzed through simulation. By optimizing sensor’s patterns, areas and geometrical parameters, the methods that maximize sensitivity of fringing electric field sensors are put forward and illustrated. The simulation is also reproduced by an experiment to ensure that the method is feasible and reliable. The results of experiments are inspiring in that they prove that the sensor can work well for protection of chips and has the advantage of universal applicability, low cost and high reliability.
DATA SYNCHRONOUS PROCESSING AND DEVICE ON THE MONITORING OF ELECTRIC POWER QUALITY

王宾,潘贞存,赵建国,时丽君

DOI: https://doi.org/10.3321/j.issn:1000-1026.2002.11.011

2002-01-01

Abstract:It is necessary to perform real-time monitoring and analysis of the network for finding the interference sources to improve and supervise the power quality. The monitoring system based on conventional SCM can hardly satisfy the actual need for accuracy and speed. A new distributed monitoring system based on DSP chip-TMS320F206 is developed to monitor and analyze all outlets in a substation and to store historical data. In order to improve the measuring accuracy, the method of data synchronous processing is introduced in detail, such as noise pre-processing, digital anti-aliasing filtering and the software sampling method at a fixed frequency. High performance chips such as TMS320F206. MAX125 are used to meet the requirements of the device for hardware, greatly increasing the accuracy of the device. At the same time, two normalized factors capable of reflecting the degree of harmonic pollution and degree of asymmetrical pollution for an asymmetrical 3-phase system are added to quantitatively determine the pollution degree of the power system.
Design of Signal Acquisition System of Photodiode Array Based on DSP

Wang Hao

DOI: https://doi.org/10.3969/j.issn.1001-182X.2011.05.011

2011-01-01

Abstract:A design of the signal acquisition system of photodiode array based on DSP is introduced in this paper.The character s of DSP chip in TMS320F2808 and photodiode array chip in S4111-16Q are discussed.A circuit between the chip S4111-16Q and the chip TMS320F2808 is designed.
An economical rapid control prototyping system design with MATLAB/Simulink and TMS320F2812 DSP

Xianmin Chen,Xinglong Gong,Huixing Zhou,Zhenbang Xu,Y. G. Xu,CunJun Kang

2010-01-01

Abstract:Rapid control prototyping (RCP) is now the typical method used by engineers to develop and test their control strategies, but the commercial RCP systems are too expansive for researchers to use. This paper presents an economical RCP (eRCP) system based on MATLAB/Simulink and the Target Support Package TC2 toolbox. A TI TMS320F2812 DSP based real-time control board for 4 axes mechatronic system and data acquisition was developed for the eRCP system. The eRCP system has functions for symbolic model development, automatic code generation, variable monitoring, and parameter tuning. A complex controller for the linear motor driven double inverted pendulum (LMDDIP) was implemented by the eRCP system to demonstrate the performance of the developed system.
Research on the Expressdsp-Compliant Algorithms

Yun Wu,Yong Zhao,Jianshi Li

DOI: https://doi.org/10.1109/wkdd.2008.132

2008-01-01

Abstract:Digital signal processor (DSP) algorithms are sets of rules that specifies the order and form of arithmetic operations that are used on specified sets of data. The implementation of these DSP algorithms is often very different from one application system to another because systems have, for example, different memory management policies and I/O handling mechanisms. This paper targets these algorithms and assists the reader with making the algorithms compliant with the TMS320 DSP algorithm standard which is part of TI's eXpressDSPTM technology initiative. Finally, the authors briefly introduced DSP architecture optimization for DSP algorithms.
Design of high speed synchronous multi-channel data acquisition and processing system based on TMS320C6747

Yan Hongcheng,Liu Wenyi

DOI: https://doi.org/10.1109/ICCAE.2010.5451785

2010-04-19

Abstract:Many signal processing applications like blind source signal separation, audio beam etc, require multi-channel synchronous data acquisition. These applications require signal acquired from multiple channels to be digitized synchronously to preserve the phase relationship. In this paper, we present the design and implementation of a high speed synchronous multi-channel data acquisition and processing system based on ADS8365, FPGA and DSP. The design takes ADS8365, XC3S200 and TMS320C6747 as the core devices to implement 12 channels of analog signal synchronous data acquisition and real-time processing. FPGA controls A/D synchronously sampling 12 channel of signal after they pass through the conditioning circuits, then, writes the data into an internal FIFO. The internal FIFO will trigger the interrupt of DSP after it is half-full. Finally, DSP will read the FIFO data and make real-time processing. The system test results show that the signal-to-noise ratio of the system is 67.13dB which meets the design requirements.

Engineering,Computer Science
Development of a TLP System with a Novel Current Sampling Technique for ESD Protection Applications

Yu Lu,Yang Hong,Yuhua Cheng

DOI: https://doi.org/10.1109/EDTM50988.2021.9420937

2021-01-01

Abstract:This paper presents a TLP test system with a new current sampling method, which has the advantages of simpler structure, higher theoretical bandwidth and higher upper limit of test current. ESD protection properties of both semiconductor and gNEMS devices were tested with the developed TLP testing machine and good testing results are achieved.
Design of AC Drive System Based on DSP TMS320F2812

HUANG Da-wei,ZHANG Wen-kai,YU Ai,YANG Geng

DOI: https://doi.org/10.3969/j.issn.1000-100x.2005.02.001

IF: 5.967

2005-01-01

IEEE Transactions on Power Electronics

Abstract:The paper presents the configuration of control board based on DSP TMS320F2812,which is used in motion control system,discusses some details in the designing hardware and programming with C language,and finally,provides experimental results of the system.Great attention has been paid to specialties of TMS320F2812 power supply system and A/D modle in hardware.C language program is used for designing the software.It is of benefit to modularization,mainte-nance and transplant of software by usage of DSP′s high operation ability and its variant internal and external resources.Parts of experimental results show the feasibility of design.
Control technology of digital Boost-PFC based on DSP

LI Xiao-ming,LV Zheng-yu

DOI: https://doi.org/10.3969/j.issn.1001-4551.2008.01.034

2008-01-01

Abstract:To reduce the harmonic pollution caused by power electronic devices,transducers should be improved by adding a powe factor cortection(PFC) circuit before accessing into network.The main principle of digital PFC based on TMS320LF24007 was discussed,and then values of the circuit's parameters were given.A small-signal dynamic model of the system was established,the method for digital control was analyzed,and the designed software flow was given.Finally,an experimental prototype was set up to verify the theory,and the rather good results were obtained.

Research on sampling method for protective device based on TMS320F2812

Research of Wireless Electrocardiograph Signal Sampling System

Design of Experimental Switched Reluctance Drive System Based on DSP

Study of Turn-on Characteristics of SCRs for ESD Protection with TDR-O and TDR-S TLPs

Novel Sampling Algorithm for Dsp Controlled 2 Kw Pfc Converter

Hardware Design of ECG Reccording System Based on TMS 320F2812

Research of simulation system of pv on-grid power generation based on dsp

Design of Virtual Device System Based on DSP

Design Of Comprehensive Motor Protector Based On Improved Sliding-Window Iterative Dft Algorithm

A Novel and Powerful TCAD Methodology to Evaluate Performance of ESD Protection Devices

Analyse of Protection Devices' Speed Performance against ESD under CDM Using TCAD

A smart resampling scheme for digital substation relay protection

Fringing Electric Field Sensors for Anti-Attack at System-Level Protection

DATA SYNCHRONOUS PROCESSING AND DEVICE ON THE MONITORING OF ELECTRIC POWER QUALITY

Design of Signal Acquisition System of Photodiode Array Based on DSP

An economical rapid control prototyping system design with MATLAB/Simulink and TMS320F2812 DSP

Research on the Expressdsp-Compliant Algorithms

Design of high speed synchronous multi-channel data acquisition and processing system based on TMS320C6747

Development of a TLP System with a Novel Current Sampling Technique for ESD Protection Applications

Design of AC Drive System Based on DSP TMS320F2812

Control technology of digital Boost-PFC based on DSP