Abstract:The C/SiC-Cu3Si-Cu interpenetrating composites were prepared by the ceramization and metallization of carbon fiber reinforced carbon aerogel (C/CA) preforms. Fracture mechanical and ablation behaviors as well as their dependence on metal addition and PyC interface thickness were investigated. With the presence of metallic components, the C/SiC-Cu3Si-Cu composites show pseudo-plastic fracture, typical brittle-plastic mixed fracture, and then ladder-like fracture with the PyC interface thickness increasing due to the co-existence of ductile and brittle components, obviously different from the fracture of conventional ceramic matrix composites. The composite with 3.0 lm-thick interface has the highest flexural strength of 292.8 MPa due to the proper interfacial bond strength and residual compressive stress. The composite with 1.9 lm-thick interface has the highest work of fracture but relatively low fracture toughness due to the abundant modes of crack propagation. The anti-ablation property is deteriorated with increased PyC thickness due to the weakened transpiration cooling effect and reduced oxide scale quality. The composite with 0.9 lm-thick interface exhibits lower mass and linear ablation rates of 0.054 mg cm-2 s-1 and 0.018 lm s- 1 after ablation at 2200 degrees C for 600 s, respectively. This work provides vital insights into the control of the overall performance of carbon fiber reinforced ceramic-metal matrix composites.

The Fracture Mechanism of As-Cast and Extruded Sicp/Az91 Composites Fabricated by Stir Casting

Forming process of hot-extruded SiCw/6061AI composites(I)

Study on Fracture Behavior of Particulate Reinforced Magnesium Matrix Composite Using in Situ SEM

Microstructure and Mechanical Properties of Sicp/Az91 Composite Deformed Through A Combination of Forging and Extrusion Process

Evolutions of Microstructure and Mechanical Properties for Sicp/Az91 Composites with Different Particle Contents During Extrusion

Processing, Microstructure and Mechanical Properties of SiCp/AZ91 Mg Matrix Composites Fabricated by Squeeze Casting

Processing and Mechanical Properties of Sic Particulate Reinforced Az91 Composites Fabricated by Stir Casting

Fracture Behaviour of SiCp/Al Composites with Network Architecture

Interfacial Microstructure and Fracture Behavior of SiC Whisker Reinforced Magnesium Matrix Composites

Study on Behavior of Dynamic Fracture in SiC Nanoparticles Reinforced Magnesium Matrix Composites

Effects of Bimodal Size SiC Particles on the Microstructure Evolution and Fracture Mechanism of AZ91 Matrix at Room Temperature

Interfacial Reaction In Squeeze Cast Scw/Az91 Magnesium Alloy Composite

The Interfacial Characteristic of Sicp/Az91 Magnesium Matrix Composites Fabricated by Stir Casting

Hot Extrusion of SiCp/AZ91 Mg Matrix Composites

Effect of Hot Extrusion on Microstructures and Mechanical Properties of SiC Nanoparticles Reinforced Magnesium Matrix Composite

The deformation and fracture behavior of SiCw/AZ91 magnesium matrix composite during in-situ TEM straining

Hot Deformation Behavior of Sicp/Az91 Magnesium Matrix Composite Fabricated by Stir Casting

Fracture Mechanical and Ablation Behaviors of C/SiC-Cu3Si-Cu Interpenetrating Composites and Their Dependence on Metal Addition and Interface Thickness

Microstructure and Elevated Tensile Properties of Submicron SiCp/AZ91 Magnesium Matrix Composite

Aging Behavior of the Extruded SiCp-reinforced AZ91 Mg Alloy Composite

Microstructure and Mechanical Properties of Sicp/Mg-Zn-Ca Composites Fabricated by Stir Casting