Abstract:The microstructural characteristics and morphological attributes of the target material, along with its intrinsic properties, can significantly influence the performance of the resultant film. Currently, commercially available nickel-vanadium targets employed in the industry have not been subjected to investigations aimed at controlling grain size and grain orientation. This study examines the effects of unidirectional rolling at room temperature, combined with substantial deformation, on the alterations in microstructure, texture evolution, and mechanical properties of the NiV7 alloy. The process of severe plastic cold rolling leads to a continuous elongation and refinement of the grains. The changes in microstructure and texture of the cold-rolled sheets were analyzed using electron backscatter diffraction (EBSD) technology. At an 80% reduction, a significant number of sub-grains are observed, which transform into deformed grains as the reduction reaches 95%. With a thickness reduction of 96.6%, the average grain size is approximately 1.10μm. Further increases in reduction do not lead to significant alterations in the grain structure; instead, the grain orientation progressively becomes more uniform with higher levels of deformation. The combination of substantial deformation and lower rolling rates results in an increased number of high-angle grain boundaries. The alloy displays various textures throughout the rolling process, including S-type, copper-type, brass-type, fiber, and cubic textures. Notably, the prevalence of S-type and fiber textures diminishes as the degree of deformation increases, while the cubic texture becomes increasingly prominent. Upon achieving a reduction of 95%, the cubic texture emerges as the dominant texture. A transmission electron microscope (TEM) was utilized to examine the extensive array of dislocations, dislocation cells, dislocation walls, and shear bands generated during the cold rolling process. At a deformation level of 96.6%, the ultimate tensile strength of the alloy demonstrates a significant enhancement, attributed to mechanisms of dislocation strengthening and grain strengthening, reaching a value of 1231±20 MPa, accompanied by a post-fracture elongation of approximately 2%. The ultimate tensile strength exhibited an increase of 781±20 MPa compared to the sample prior to the rolling process; however, there was a notable reduction in plasticity.

Effect of Temperature on Microstructure and Texture of Rolled Ni–9·3 At-%W Alloy

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Evolution of Microstructure, Texture and Topography During Cold Rolling and Recrystallization of Ni–5at.%W Alloy Substrate for Coated Conductors

Study on Evolution of Microstructure and Texture of Cold-rolled Ni9W Alloy with Large Deformation

Microstructure and Texture Evolution of Cu-Ni-P Alloy after Cold Rolling and Annealing

Microstructure Evolution and Texture Characteristics of Pure Nickel N6 During Cold Rolling Process

Effect of hot rolling on microstructure and tribology behaviors of Ti−50.8Ni alloy

Effect of Cold Rolling and Hot Rolling on Recrystallization Texture and Superelastic Properties of Ti–30Zr–10Nb–2Sn Shape Memory Alloy

Effects of Cold Rolling Reduction Rate on the Microstructure and Properties of Cu-1.16Ni-0.36Cr Alloy after Thermo-Mechanical Treatment

Effect of cryogenic rolling on the microstructure and texture of CuCrZr alloy

Effect of Warm Rolling Temperature on the Microstructure and Texture of Microcarbon Dual-Phase (DP) Steel

Effect of Cold Rolling on the Microstructure and Mechanical Behaviors of High-Nitrogen and Low-Nickel Alloy

Microstructure, Texture and Mechanical Properties of Ti-43Al-9V-0.2Y Alloy Hot-Rolled at Various Temperatures

Effect of Cold Rolling Process on Microstructure, Texture and Formability of 00cr21monbti Ferritic Stainless Steel

Effect of Aging Temperature on Microstructure and Properties of Cold-Rolled Cu-Ni-Si Alloy

Impact of Non-Isothermal Warm Rolling on Microstructure, Texture and Mechanical Properties

Effect of Rolling on the Microstructure and Mechanical Properties of (fecrni)94ti3al3 Medium Entropy Alloy Fabricated Via Selective Laser Melting

Rolling parameters, microstructure control, and mechanical properties of powder metallurgy Ti–44Al–3Nb-(Mo, V, Y) alloy: The impact of rolling temperatures

Microstructure and texture evolution in warm-rolled fine-grained tungsten

Effect of Electroplastic Rolling on Deformability and Oxidation of NiTiNb Shape Memory Alloy

Severe plastic cold rolling effects in Nickel-Vanadium alloy: Microstructure, texture evolution and mechanical properties