Abstract:For development of thin bioactive coatings on metal implants, a dense and uniform apatite layer was coated onto titanium (Ti) implants in situ by using a new biomimetic method, which is composed of apatite nucleation and growth steps in simulated body fluid (SBF). Analysis of the coatings by thin film X-ray diffraction and scanning electron microscopy-energy dispersive X-ray microanalysis (SEM-EMPA) before implantation showed that its characteristics were very similar to those of natural bone. The coated and uncoated rectangular plates were bilaterally implanted into the tibial proximal metaphyses of rabbits. After 6, 10 and 25 weeks post-implantation, the bone bonding and bone formation at the bone-implant interfaces were evaluated by a detachment test and undecalcified histological examination. Mechanical testing in tension showed that the failure load of apatite layer-coated Ti implants was significantly higher than that of uncoated control at each time period (all P < 0.001). Histologically, it was shown that bone was deposited directly onto the apatite coating without any intervening soft tissue, while in the paired controls, interpositional soft tissue was seen at the bone-implant interface. By SEM-EPMA, a uniform calcium- and phosphorus-rich layer was detected between the coated implants and bone, but not in uncoated controls at either earlier or later time periods. The results indicate that the apatite layer deposited on Ti in situ may significantly increase the bone bonding strength by providing a bioactive surface, which allows for an early bone apposition to the implant. In addition, the apatite layer-coated Ti produced by the biomimetic process may fulfil the requirements of favourable thin coatings and strong adhesion at the metal-coating interface.

Porous Titanium by Fiber Sintering and Its Biomimetic Ca-P Coating

[Experimental Study of Fast Formation of Biomimetic Apatite Coatings on Pure Titanium Surface].

[Fast Formation of Biomimetic Apatite Coatings on Pure Porous Titanium Implant's Surface].

Porous Titanium and Silicon-Substituted Hydroxyapatite Biomodification Prepared by a Biomimetic Process: Characterization and in Vivo Evaluation.

Innovative Fabrication of Porous Titanium Coating on Titanium by Cold Spraying and Vacuum Sintering

Fabrication of Porous Titanium and Biomimetic Deposition of Calcium Phosphate

In Situ Synthesis and Fabrication of Tricalcium Phosphate Bioceramic Coating on Commercially Pure Titanium by Laser Rapid Forming

Longer-Term Mechanical And Biological Evaluation Of Titanium Alloy Coated With Apatite Layer

Surface Modification of Titanium by Hydroxyapatite/CaSiO3/Chitosan Porous Bioceramic Coating

Bone-like Apatite Growth on Controllable Macroporous Titanium Scaffolds Coated with Microporous Titania

Bone Responses to Rough Titanium Implants Coated with Biomimetic Ca-P in Rabbit Tibia.

Apatite Layer-Coated Titanium for Use As Bone Bonding Implants

The Study of Surface Modification and Biocompatibility of Porous Titanium

Enhancement of the Bioactivity of Alkali-Heat Treated Porous Titanium by Pre-Calcification

Preparation, Microstructure and Mechanical Properties of Porous Titanium Sintered by Ti Fibres

Fabrication and Characterization of Bioactive Porous Titanium

Study on Porous Titanium Biomedical Materials

Bioinspired Fabrication of Calcium-Doped TiP Coating with Nanofibrous Microstructure to Accelerate Osseointegration

Fabrication of Porous Titanium with Biomechanical Compatibility

Biomimetic coating of calcium phosphate and bovine serum albumin on bioactivated titanium

Fabrication of bovine serum albumin/calcium phosphate bioactive coating on porous titanium scaffolds