Abstract:With the continuous improvement of various armor protection technologies, the armor protection performance has increased significantly, and then the damage performance requirements of armor-piercing ammunition have also increased. In order to improve the penetration ability of the liner, a new three-layer liner structure is designed in this paper. The jet forming process was simulated by AUTODYN software. The mechanism of shaped jet forming of three-layer liner was studied. The reason why the penetration depth of three-layer liner was higher than that of ordinary liner was explained. The influence of three-layer liner on the propagation of detonation wave and the change of pressure when detonation wave acted on liner were found, which provided a new idea for improving the penetration depth of jet. The influence of liner material, cone angle and stand-off on jet forming and penetration was also studied by orthogonal optimization experiment, and the structural parameters with the best penetration performance were obtained. The results show that the pressure at the convergence point increases first and then decreases during the formation of the jet of the three-layer liner. The pressure at the convergence point when the three-layer liner material is from low impedance to high impedance from the outside to the inside is much larger than the pressure at the convergence point from high impedance to low impedance. When the three-layer liner material is Al 2024-Copper–Tantalum from the outside to the inside, the pressure at the convergence point of the three-layer liner at different times is higher than that of the double-layer liner and the single-layer liner. Reasonable matching of different impact impedance materials in the three-layer liner can greatly improve the pressure value of the detonation wave acting on the cone liner. The maximum pressure at the convergence point on the axis is 39.10 GPa, which is 22.00% higher than that of the double-layer liner at the convergence point, and 53.03% higher than that of the single-layer liner at the convergence point. The orthogonal design test scheme is simulated and analyzed. The penetration depth is taken as the observation index, and the range analysis is adopted. The results show that the material matching of the three-layer liner has the greatest influence on the depth of the jet penetrating the target plate, followed by the cone angle of the three-layer liner. Relatively speaking, the stand-off has the least influence on the result. Reasonable matching of materials with different impact impedances in the three-layer liner can maximize the penetration depth of the jet into the target plate.

Experimental Study on a New Way to Form Shaped Charge Projectiles with Fins

Formation of explosively-formed projectile with tail fins using polygonal charges

Study on Formation of EFP with Fins of Hexagonal Liner

Explosively formed projectile with fins

Simulation Study on EFP with Stable Tail Fins Formed by Polygonal Shaped Charge Liner

Formation of Shaped Charge Projectile in Air and Water

Experimental research on the propulsion performance of fish-like caudal fins

Simulation Study on Formation Mechanism of Tapered & Spherical Group Liner Warhead

Study on Forming Law and Penetration of a Spherical Cone Composite Structure Liner Based on the Explosion Pressure-Coupling Constraint Principle

Study On The Influences Of Ignition Position On The Formation Of Shaped Charge With Double-Layer Spherical Segment Liners

Numerical Simulationand Analysis of a New Double Shaped Charge Liner Formed Penetrator

Structural design of the fluted shaped charge liner using multi-section optimization method

A study on the surface overpressure distribution and formation of a double curvature liner under a two-point initiation

Experimental and numerical study on the flight and penetration properties of explosively-formed projectile

The Influence of Closed-Cell W-Shaped Liner Parameters on the Penetration Performance of Integral Annular Shaped Charge

Study on the detonation wave propagation of shaped charge with three-layer liner and its driving characteristics to liner

Simulation Study on Expansive Jet Formation Characteristics of Polymer Liner

Experiment Study on the Forward Charge Blast Effect on the Follow-Through Charge of Tandem Warhead

Numerical Simulation on Jet Formation of a New Star Shaped Liner

Formation and Penetration Properties of a Shaped Charge with Zr41.2Ti13.8Cu12.5Ni10Be22.5 Liner

Application of W/Zr amorphous alloy for shaped charge liner