Two kinds of energy efficiency of district cooling systems

Ma Hongquan,He Mengchun,Long Weiding

DOI: https://doi.org/10.3969/j.issn.1002-8501.2011.04.006

2011-01-01

Abstract:Deduces the formulas of the two kinds of energy efficiency,one for pre-design stage and one for verification after operating,and analyses the main influence factors,providing references for the design and analysis of district cooling systems.

What problem does this paper attempt to address?

Comparative Study on Heating and Cooling Systems Integrated with Energy Storage

Zhao Yuan,Yuan Jing,Xu Zhixiang,Dai Fu,Ma Hang,Zheng Menglian

DOI: https://doi.org/10.1051/e3sconf/202336902011

2023-01-01

E3S Web of Conferences

Abstract:Taking a commercial building in Shanghai as an example, a list of cooling and heating systems are established and operation strategies are formulated. Based on the precondition that the excess electricity can be sold to the grid, the primary energy utilization rate and economices of the energy supply schemes are analyzed. The results show that compared with the traditional heating and cooling supply method, the combined cooling, heating, and power systems have better energy-saving and economic benefits. Additionally, the inclusion of the thermal energy storage yields additional economic benefits (up to 36% reduction in the CO2eq emissions and up to the 21% reduction in the total annual cost). Under the following-electric-load operation mode, the role of the thermal energy storage is to alleviate the temporal mismatch between the electric demand and the heating or cooling demand. To be specific, in the combined cooling, heating, and power systems, the total annual cost is reduced by up to 5.8% and the annual carbon dioxide equivalent emissions are reduced by up to 2.4% when the thermal energy storage is used. While under the following-electric-price operation mode, the performance of the CCHP system is largely subject to the natural gas price. Last, although heat pump systems are often regarded as efficient systems owing to the relatively high coefficient of performance of the heat pump, the energy supply through the heat pump systems may be carbon-emission-intensive currently.
Energy consumption analysis of district cooling systems

Zhu Yingxin,Jiang Yi

DOI: https://doi.org/10.3969/j.issn.1002-8501.2008.01.009

2008-01-01

Abstract:In order to clarify energy consumption problems with district cooling systems,sets out energy consumption level by a detailed analysis of two classic district cooling system case studies in Japan.Comparing with the cooling and heating energy consumption data of Chinese typical public buildings,points out the ultimate causes for the high energy consumption of district cooling systems.Based on an analysis of some successful district cooling projects in developed countries,discusses the problems encountered in district cooling systems.Considers that the energy saving preconditions for district cooling systems are sufficient concentration of cooling users and enough low-cost natural cold sources.
Seasonal Energy Performance Evaluation with New Perspective on Partial-Coupling Ejection-Compression Solar Cooling System for Modern City Buildings

Yingjie Xu,Qiqi Shi,Ning Chen,Xi Shen,Chunyan Wang,Xiaohong Han

DOI: https://doi.org/10.1016/j.enconman.2021.113875

IF: 10.4

2021-01-01

Energy Conversion and Management

Abstract:Space cooling accounts for high percentage of energy consumption in modern city building. To improve energy utilizing efficient of space cooling, a new system based on solar partial-coupling ejection-compression refrigeration cycle is studied. Builds are assumed to be located at modern city of Shanghai, with area of 100 m(2) for each floor. With a model combining cooling system, building, and weather information, comparative analysis is carried out hourly, using new perspective of total primary energy, during the whole cooling season. For the building with a common height of six-storey in modern city, partial-coupling ejection-compression refrigeration cycle reveals obvious superiority in electric coefficient of performance, solar factor, thermal coefficient of performance, total primary energy, with best value of 6.2, 1, 3.6, and 14 kW, respectively, which helps to reduce carbon dioxide emission. The remarkable difference in auxiliary heat between partial-coupling ejection compression refrigeration cycle and traditional ejection-compression refrigeration cycle results in the great primary energy saving of partial-coupling cycle, which reveals significant superiority and good suitability of partial-coupling cycle used in multi-stroey buildings in modern city.
How to develop district cooling in China with success

Gang Wang,Yingxin Zhu

2007-01-01

Abstract:This paper aims at pointing out that how a District Cooling system can be a more energy efficient solution compared with a decentralized cooling solution. In order to give a fair comparison, the author applies equivalent electric power coefficient of performance. This comparison approach will be instructive for designing an energy efficient cooling solution in China. Firstly, the paper gives the definition, components and possible energy source of a District Cooling System. Secondly, the author points out the theoretical advantages and practical problems of this solution for cooling of the built environment. Thirdly, the paper analyses several key factors in several DCS cases, including free cooling possibility, cooling load density and stability, cold water supply and return temperature difference in the transportation and distribution network through several case studies. Finally the author points out the key difference between District Cooling and District Heating and concludes that like decentralized cooling solution, District Cooling is just a cooling solution and only under very specific circumstance this solution can be considered and being competitive in terms of energy efficiency with decentralized cooling solution.
Performance assessment and improvement of district cooling system: A case study of enhancing energy efficiency of hospital buildings

Xi Bai,Weidong Ma,Junjie Huang,Caihua Liang,Xiaosong Zhang

DOI: https://doi.org/10.1016/j.csite.2024.104187

IF: 6.268

2024-04-01

Case Studies in Thermal Engineering

Abstract:In addressing the performance degradation issue of district cooling systems, although various evaluation methods exist, they either neglect design objectives or focus on independent equipment, overlooking the synergies between devices. Therefore, the study establishes a comprehensive performance assessment framework, encompassing efficiency, environmental impact, economic factors, and technological aspects. The Analytic Hierarchy Process (AHP) and Entropy Weight Method are employed to determine the comprehensive weights for each indicator. In a specific case study, the operational status of an existing district cooling system is assessed, considering collaborative interactions among equipment. A fault tree analysis is applied to scrutinize 13 potential events contributing to system inefficiency and their logical relationships with relevant parameter variations. Based on these findings, specific optimization measures, such as check valve replacement and adjustments to pump and fan frequencies, are recommended. The performance of the optimized system is then re-evaluated, demonstrating substantial improvements with comprehensive performance scores increasing from 18.3 to 27.8 and 29.5, respectively.

thermodynamics
Influence of Occupant Behavior on the Efficiency of A District Cooling System

Xin Zhou,Da Yan,Guangwei Deng

DOI: https://doi.org/10.13614/j.cnki.11-1962/tu.2015.10.15

2013-01-01

Abstract:The related researches about district cooling systems are very limited in China, which leads to several misunderstandings and improper applications in engineering practices. Under this background, a real project with the district cooling system in a residential community is analyzed in this paper, and the equipment performances are discussed. It is found that the occupant behavior has a key influence on the efficiency of a district cooling system. Through the simulation which accounts for the different use modes of residents, the applicability analysis about the application of district cooling systems in residential buildings is conducted. Through the research, it can be concluded that the district cooling system can only be high efficiency with a concentrated terminal load profile. And for the popular occupant behavior in residential buildings in China, it's worth examining whether the applicaition of district cooling systems is suitable.
Method of Defining Heating and Cooling Period for Residential Buildings in Hot Summer and Cold Winter Zone

FU Xin,QIAN Xiao-qian,QIAN Kuang-liang,DONG Kai,RUAN Fang

DOI: https://doi.org/10.3785/j.issn.1008-973x.2017.04.013

2017-01-01

Abstract:Large amounts of actual measured meteorological data of 20 typical cities in hot summer and cold winter zone in China between 1971 and 2003 were analyzed.There exist wide differences in climatic conditions among cities in this climate region, as reflected in many aspects like the average temperature and diurnal range in coldest(hottest) month, the number of days in which the daily average temperature was less than or equal to 5 ℃ (higher than or equal to 25 ℃), the heating and cooling degree day, etc.The reasonability of calculation periods set by three existing relevant standards in China was investigated, and a new defining method of calculation period was proposed based on actual measured meteorological data and discreteness analysis.The results of energy consumption simulation for residential buildings with the Design Builder software indicate that different calculation periods not only affect the total heating and cooling consumption simulation result, but also change the ratio of them.
On-site measurement and analysis of distribution energy efficiency of centralized heat pump heating systems

Zhongjun Wu,Qingpeng Wei,Jiewen Deng,hui Zhang

2017-01-01

Abstract:Presents the measurement results of distribution energy efficiency of thirteen centralized heat pump heating systems in a city in cold zone of China.Compares the rated energy efficiency ratios of distribution systems of these projects with measured ones.Analyses the energy consumption percentage of main chillers,heat source water distribution system and hot water distribution system.Summarizes the typical problems resulting in higher energy consumption of distribution system including large flow rate and small temperature difference,low operational efficiency of pumps and large pipeline resistance.Puts forward some suggestions to improve the distribution energy efficiency of centralized heat pump heating systems.
The Energy Efficiency and Economic Feasibility Analysis of the Distributed Absorption Cooling Combined with District Heating System

Qunli Zhang,Lin Fu,Lihua Li,Hongfa Di

DOI: https://doi.org/10.1115/es2009-90070

2009-01-01

Abstract:The distributed absorption cooling based district heating system was investigated in order to utilizing the reject heat from the combined heat and power (CHP) plant in summer.Compared with the electric compressor cooling, the energy efficient and cost-effectiveness of the distributed absorption cooling were furthermore analyzed by the Fuel Energy Saving Ratio (FESR) method. The sensitivity of some variables, such as the average electric efficiency, heating and electric generation efficiency of the CHP system, and the coefficient of performance (COP) of the chiller, were analyzed. The marginal heating price of the distributed absorption cooling can be obtained. According to the evaluation results, the applicability of the distributed cooling with district heating system is limited by the lower energy efficiency and economical benefits. The approaches to increase the energy efficiency were suggested in this paper. The improved distributed absorption cooling combined with liquid desiccant dehumidification which has higher heating utilization efficiency was put forward and analyzed, and the energy efficiency evaluation results showed that the improved distributed cooling has higher energy efficiency and economical benefits, and great applicability.
Case study on HVAC energy efficient optimization and renovation(Part Ⅰ):Water chillers

Chang Cheng,Wei Qingpeng,Cai Hongwu,Chang Liang

DOI: https://doi.org/10.3969/j.issn.1002-8501.2010.08.009

2010-01-01

Abstract:With a typical case,discusses the key factors affecting energy consumption and efficiency of chillers,and presents the methods to optimize chiller efficiency,providing reference for buildings with large chillers.
Case study on HVAC energy efficient optimization and renovation(Part Ⅳ):Cooling towers

Shen Qi,Wei Qingpeng

DOI: https://doi.org/10.3969/j.issn.1002-8501.2010.08.012

2010-01-01

Abstract:Cooling tower is one of the most important components of central air conditioning system.Counter-flow wet-cooling towers are commonly used in large public buildings while with lower efficiency in most buildings.Taking the system composed of chillers and cooling towers as an object,puts forward the optimization way based on an overall consideration of chiller energy efficiency.Concludes a simple control strategy combined with variable frequency and high/low speed regulation for the fans of cooling tower by establishing a semi-empirical theoretical model and the renovation testing in an actual building.
The Rebound Effect in District Cooling Systems : Analysis Based on Case Studies and Surveys in China

Siyue Guo

2016-01-01

Abstract:District cooling systems are widely promoted in China now because of their higher coefficient of performance (COP). However, through the investigation of case studies, it was found that the energy use of these systems is usually much higher than that of decentralized systems. The increase of energy use is caused by the change of occupancy behavior as people tend to use cooling more when the district cooling is used, or the so-called rebound effect. This research intends to describe the difference of occupancy behavior in these two systems using quantitative analyses methods. Both case study and questionnaire surveys are used to find the relationship of usage patterns and energy consumption and analyze the reason of high energy use in district cooling systems. The main reasons cause the rebound effect are also discussed based on the case study, including the adjustability of the system, the pricing scheme and the improvement of the requirement of the indoor thermal environment. The findings suggest that in order to save energy and to weaken the rebound effect, corresponding measures both on technology development and policy are urgently needed. Future research should focus on the careful analysis of the pricing scheme. For the improvement of living standards, cooling systems are surely needed in China, but it is important that the system is suitably scaled and designed.
Cold source selection and efficiency analysis of data center cooling systems

Wang,ZhenYing,Cao,HanWen,Li,Zhen

2017-01-01

Kung Cheng Je Wu Li Hsueh Pao/Journal of Engineering Thermophysics

Abstract:This paper analyzed the energy efficiency of two commonly used cooling systems (including the air-cooled type and the water-cooled type) in data centers according the climatic characteristics of different climate zones based on the energy consumption measuring results of a nedium size data center.The results revealed the influence of the seasonal and regional climate differences on the performance of the data center cooling systems and also showed the application advantages of the air-cooled and water-cooled systems.An operation test on a free cooling system combining the heat pipe cycle and the vapor compression cycle was conducted.The results concluded the available time and energy saving potential of the combined system in different climate zones,which can be used in the site selection of data centers and the optimization of the data center cooling systems.
Comprehensive and quantitative evaluation for selecting a suitable scheme of central air-conditioning during the design phase

Xiangguo Xu,Zhangqing Liu,Wei Li,Zhijiang Zhu,Ming Yan,Ping Li

DOI: https://doi.org/10.1016/j.jobe.2023.108245

IF: 7.144

2023-12-14

Journal of Building Engineering

Abstract:As for routinely selecting the number and size of chillers in central air-conditioning system, the conventional scheme in which the total cooling capacity is allocated in an equal or empirical way is generally suboptimal. A few factors are brought into consideration, and the time domain of evaluation is too short. The low suitability between the cooling load of building and the scheme selected results in an inefficient state of system during the most of operation time. Some novel methods provide long-term evaluations for selecting an efficient scheme by simulating the cooling loads then calculating the cost and performance of the scheme. However, the schemes are formed without correlating actual plants which is difficult to be applied to an actual project, and the long-term environmental impact is rarely considered. The evaluation method with a high engineering value is required. But the more complicated the method is, the more work is required. The relationship between the benefits and the costs is unknown. Therefore, this study proposes three evaluation methods at different levels. From simple to complex, the three methods are corresponding the cooling load curve of building calculated through EnergyPlus to the performance curves of chillers, system simulation using TRNSYS and co-simulation based on BCVTB respectively. A case study using a hospital building located in Zhejiang province, China combined with equipment list was conducted to demonstrate the evaluation process. The results calculated by different methods and the various indexes of different schemes were compared to illustrate how to optimize the scheme selection during the design phase in order to select a suitable scheme for a certain building reducing the energy consumption and carbon emission.

construction & building technology,engineering, civil
Comparison of the energy performance of novel dual-temperature cooling systems: From field testing to simulations

Zixu Yang,Naini Zhao,Hongli Sun,Hengxin Zhao,Yifan Wu,Mengfan Duan,Borong Lin

DOI: https://doi.org/10.1016/j.jobe.2023.106920

IF: 7.144

2023-01-01

Journal of Building Engineering

Abstract:Air conditioners (AC) face the challenge of low energy efficiency in field operation. Considering that the performance of dual-temperature systems remains unexplored, especially in different climate zones, an AC with a fiat heat pipe and different temperature controls was tested in an experimental chamber. The energy efficiency increased by 14% compared to that of an AC with a dehumidification mode. Furthermore, three novel systems that optimize the dual-temperature cooling process are proposed. These include an AC with a twin-cylinder compressor, AC with medium/low-pressure ejectors, and AC with high/low-pressure ejectors. The performance of these ACs was analyzed under different conditions. The maximum EER of the four ACs was 9.13, 9.91, 9.54, and 10.68, respectively, for an evaporation temperature of 10 degrees C and different condensation temperatures and part-load ratios. The nominal EER of the three dual-temperature systems increased by 9.4, 6.8, and 19.7%, respectively, with respect to the conventional system. The seasonal energy efficiency ratio of the three dual-temperature systems increased by approximately 5.8-18.8%, 6.3-19.9%, 6.0-18.8%, and 3.9-17.6% in four different climate zones, respectively. Our results indicate that the twin-cylinder compressor system has the highest po-tential for applications in high-efficiency cooling systems.
Evaluation and optimization of district energy network performance: Present and future

Yang Wang,Shanhong Zhang,David Chow,Jens M. Kuckelkorn

DOI: https://doi.org/10.1016/j.rser.2020.110577

IF: 16.799

2021-04-01

Renewable and Sustainable Energy Reviews

Abstract:<p>The building sector accounts for the largest portion of total final energy consumption in most countries, and is responsible for around one third of carbon emissions, which have been regarded as the cause for global warming and climate changes. District energy network, which can supply consumers with heating/cooling and electricity, is an effective and proven approach to enhance energy efficiency and reduce carbon emissions. Currently, the approach of integrated energy systems (including renewable energy) tends to be increasingly necessary and significant for the district energy network. This article presents a comprehensive review of energy performance of district energy networks, focusing on optimization and evaluation of district heating network combining with other relevant energy systems and renewable technologies. This review consists of the concept of district energy network, typical applications of district energy network, and significant literatures of energy performance of various energy networks based on theoretical modelling and analysis, physical experimental studies and numerical simulations. Furthermore, over 30 factors affecting energy performance have been substantially investigated and assessed. This review has demonstrated that main effects on energy network performance are significantly linked to configurations and capacities of system, climate conditions (locations and time), and the interaction between various factors. An optimal overall performance of district energy network would need to integrate several advanced energy systems, e.g. a balanced energy network.</p>

energy & fuels,green & sustainable science & technology
DESIGN AND OPTIMIZED OPERATIONAL STRATEGY OF A DISTRICT COOLING AND HEATING SYSTEM BASED ON GROUND SOURCE HEAT PUMPS

Tianle Hu,Yi Jiang,Xiaoyun Xie

DOI: https://doi.org/10.18462/iir.gl.2018.1189

2018-01-01

Abstract:A comprehensive district heating and cooling (DHC) system design is presented. Large-scale ground source heat pump (GSHP) with thermal energy storage system is applied in the DHC system. Normally, the compressor of a ground source heat pump works at a very wide range of compression ratios, and thus the annually overall performance is comparatively low. Through simulation evaluation, the annual cooling and heating performance of the ground source heat pump is enhanced by increasing the mean temperature of the ground and thus narrowing the work range of compression ratios. The hourly operation strategy of the heat pumps and thermal storage system is proposed to decrease the energy cost and match the tiered pricing of power consumption. In addition, heat pumps always work near the maximum efficiency point by utilizing the coordinated thermal energy storage system.
Analysis of District Cooling System with Chilled Water Thermal Storage in Hot Summer and Cold Winter Area of China

Lun Zhang,Jun Jing,Mengfan Duan,Mingyang Qian,Da Yan,Xiaosong Zhang

DOI: https://doi.org/10.1007/s12273-019-0581-x

IF: 4.0083

2019-01-01

Building Simulation

Abstract:A typical district cooling system (DCS) with a chilled water storage system is analyzed in hot summer and cold winter area in China. An analysis method concerning operation modes is proposed based on measured data, which is obtained by long term monitoring and on-site measurements of cooling season. The DCS operates at partial load for a large proportion of the cooling time; in particular, the partial-load rate (PLR) can be less than 25% for more than 50% of the total cooling season. In the night, PLR reaches 5% of the peak load. Thus, it is critical to achieve efficient operation under partial-load conditions of the DCS. Installation of chilled water thermal storage presents a solution to improve the working condition of the DCS and chillers. From the beginning to the end of the cooling season, the DCS operation can be summarized by typical operation modes according to cooling demand and chiller operation. For each mode, the base-load chiller operated at a high-load rate, with an average value of 0.88, and the coefficient of performance (COP) remained in a small range, between 4.2 and 5.2. The average energy efficiency ratio (EER) of the DCS for the cooling season was 3.65 and 3.81 for Years A and B, respectively. With respect to the economics, chillers used 90.2% of off-peak electricity, at only half the price of peak electricity.
Design of district heating system with dual-temperature supply based on thermal energy discretisation and matching method

Wei Chen,Tiancheng Li,Xianting Li,Baolong Wang,Yang Cao,Wenxing Shi

DOI: https://doi.org/10.1016/j.jclepro.2023.138533

IF: 11.1

2023-08-26

Journal of Cleaner Production

Abstract:As heating requirements continue to evolve and heating technology advances, radiators and radiant floor heating devices, which require different supply-water temperatures, have gradually become the two main heating terminals in district heating systems. However, the primary return-water temperature of current solutions based on heat exchangers and heat pumps is relatively high and fails to recover waste heat from the combined heat and power plants, owing to improper use of heat sources. To address this issue, a heat exchanger network optimisation method—the thermal energy discretisation and matching method—was used to design a dual-temperature water district heating system consisting of two absorption heat pumps and two heat exchangers. The primary supply water flows through the two generators, two heat exchangers, and two evaporators of the absorption heat pumps. The radiator and floor heating return water was divided into two parts and heated by the heat exchanger and the absorber and condenser of the absorption heat pump, respectively. The performance of the designed heating station was evaluated using the coefficient of performance and the primary return-water temperature and compared with that of other district heating systems. The changes in the district heating system's configuration when the boundary conditions changed were investigated. Results showed that (1) the designed system based on thermal energy discretisation and matching method -had the lowest primary return-water temperature of 18.8 °C and the highest coefficient of performance of 5.62. (2) When the low-temperature load ratio changed from 0% to 100% while maintaining a constant total load, the system's form changed regularly. (3) When the primary supply-water temperature increased, the heating station's form remained unchanged and the capacity of the heat exchange equipment changed regularly. (4) When the secondary supply and return-water temperatures increased, the evaporation temperature of the absorption heat pump increased, resulting in a change in the system's form. This study provides valuable insight into the design of district heating systems that supply dual-temperature water under various design conditions.

environmental sciences,green & sustainable science & technology,engineering, environmental
Research on Systematic Optimization Methods for Chilled Water Systems in a High-Rise Office Building

Jiewen Deng,Shi He,Qingpeng Wei,Mei Liang,Zhigang Hao,Hui Zhang

DOI: https://doi.org/10.1016/j.enbuild.2019.109695

IF: 7.201

2019-01-01

Energy and Buildings

Abstract:The chilled water system is the major component of HVAC systems, and it consumes a large amount of energy and has significant influence on the cooling effect. To save energy and provide a comfortable indoor environment, the energy performance of the chilled water system should be analyzed and improved. This paper introduces a systematic optimization process of the chilled water system in a high-rise office building. First, the influencing factors and their characteristics are summarized and analyzed, and the results show that higher temperature difference, energy efficiency of typical devices, and lower terminal resistance contribute to the improvement in energy performance. Then, based on the analysis, a systematic optimization method is put forward considering the external factors, internal factors, and synergies between them. Finally, an optimization of the studied building is conducted, from terminals to the chiller plant, and considerable energy saving effects are achieved on the premise of ensuring the indoor cooling demand. (C) 2019 Elsevier B.V. All rights reserved.

Two kinds of energy efficiency of district cooling systems

Comparative Study on Heating and Cooling Systems Integrated with Energy Storage

Energy consumption analysis of district cooling systems

Seasonal Energy Performance Evaluation with New Perspective on Partial-Coupling Ejection-Compression Solar Cooling System for Modern City Buildings

How to develop district cooling in China with success

Performance assessment and improvement of district cooling system: A case study of enhancing energy efficiency of hospital buildings

Influence of Occupant Behavior on the Efficiency of A District Cooling System

Method of Defining Heating and Cooling Period for Residential Buildings in Hot Summer and Cold Winter Zone

On-site measurement and analysis of distribution energy efficiency of centralized heat pump heating systems

The Energy Efficiency and Economic Feasibility Analysis of the Distributed Absorption Cooling Combined with District Heating System

Case study on HVAC energy efficient optimization and renovation(Part Ⅰ):Water chillers

Case study on HVAC energy efficient optimization and renovation(Part Ⅳ):Cooling towers

The Rebound Effect in District Cooling Systems : Analysis Based on Case Studies and Surveys in China

Cold source selection and efficiency analysis of data center cooling systems

Comprehensive and quantitative evaluation for selecting a suitable scheme of central air-conditioning during the design phase

Comparison of the energy performance of novel dual-temperature cooling systems: From field testing to simulations

Evaluation and optimization of district energy network performance: Present and future

DESIGN AND OPTIMIZED OPERATIONAL STRATEGY OF A DISTRICT COOLING AND HEATING SYSTEM BASED ON GROUND SOURCE HEAT PUMPS

Analysis of District Cooling System with Chilled Water Thermal Storage in Hot Summer and Cold Winter Area of China

Design of district heating system with dual-temperature supply based on thermal energy discretisation and matching method

Research on Systematic Optimization Methods for Chilled Water Systems in a High-Rise Office Building