Abstract:In this paper, the effect of thermomechanical treatment process on the hardening behavior, grain microstructure, precipitated phase, and tensile mechanical properties of the new high-strength and high-ductility Al-10.0Zn-3.0Mg-2.8Cu alloy was studied, and the optimal thermomechanical treatment process was established. The strengthening and toughening mechanisms were revealed, which provided technical and theoretical guidance for the engineering application of this kind of high strength-ductility aluminum alloy. Al-10.0Zn-3.0Mg-2.8Cu alloy cylindrical parts with external longitudinal reinforcement were prepared by a composite extrusion deformation process (reciprocal upsetting + counter-extrusion) with a true strain up to 2.56, and the organizational evolution of the alloys during the extrusion deformation process and the influence of pre-stretching treatments on the subsequent aging precipitation behaviors and mechanical properties were investigated. The results show that firstly, the large plastic deformation promotes the fragmentation of coarse insoluble phases and the occurrence of dynamic recrystallization, which results in the elongation of the grains along the extrusion direction, and the volume fraction of recrystallization reaches 42.4%. Secondly, the kinetic study showed that the decrease in the activation energy of precipitation increased the nucleation sites, which further promoted the diffuse distribution of the second phase in the alloy and a higher number of nucleation sites, while limiting the coarsening of the precipitated phase. When the amount of pre-deformation was increased from 0% to 2%, the size of the matrix precipitated phase decreased from 5.11 μm to 4.1 μm, and when the amount of pre-deformation was increased from 2% to 7%, the coarsening of the matrix precipitated phase took place, and the size of the phase increased from 4.1 μm to 7.24 μm. The finalized heat treatment process for the deformation of the aluminum alloy tailframe was as follows: solution (475 °C/3 h) + 2% pre-stretching + aging (120 °C/24 h), at which the comprehensive performance of the alloy was optimized, with a tensile strength of 634.2 MPa, a yield strength of 571.0 MPa, and an elongation of 15.2%. The alloy was strengthened by both precipitation strengthening and dislocation strengthening. After 2% pre-stretching, the fracture surface starts to be dominated by dense tough nest structure, and most of them are small tough nests, and small and dense tough nests are the main reason for the increase in alloy toughness after 2% pre-stretching deformation.

Damping Behavior of the High Strength Aluminum Alloy Prepared by Rapid Solidification and Powder Metallurgy Process

Damping performance and mechanism of high strength aluminum alloy prepared by rapidly solidified/power metallurgy process

Microstructural Influences Caused by Different Aging Strategies on the Strain-Dependent Damping of the High-Strength Aluminum Alloy AA7075

Effects of Aging Process on the Damping Performance of ZK60 Magnesium Alloys Prepared by Large Strain Rolling

Effect of Aging Treatment on Microstructure and Damping Properties of Mg-Al-Ca-Mn-Zn Alloy

Influence of Heat Treatment on Mechanical and Damping Properties of AZ61 Magnesium Alloy

Effect of Aging Treatment on Damping Capacity in Mncunife Alloy

Effect of the Precipitated Second Phase During Aging on the Damping Capacity Degradation Behavior of M2052 Alloy

Effect of Aging Treatment on the Mechanical Properties of Die Casting Al-Mg-Si-Mn Alloys with High Strength and Toughness

Precipitation and Responding Damping Behavior of Heat-Treated AZ31 Magnesium Alloy

Damping Property of Supersaturated Znal27ce Alloy During Natural Aging

Effect of Heat Treatment on the Microstructure and Mechanical Properties of Extruded Al–4Cu–1Li–0.4Mg–0.4Ag–0.18Zr Alloy

Microstructural Characterization and Mechanical Properties of 6061 Aluminum Alloy Processed with Short-Time Solid Solution and Aging Treatment

Effects of Multi-Stage Aging Treatments on the Precipitation Behavior and Properties of 7136 Aluminum Alloy

Study on the Aging Precipitation Behavior and Kinetics of Al-10.0Zn-3.0Mg-2.8Cu Alloy by Pre-Deformation Treatment

Pre-aged and paint-baked strengthening response on the prolonged natural-aged Al-Mg-Si-Cu aluminum alloys

Effect of Aging Treatment on Tensile Behaviors of Cast Mg-9Gd-4Y-0.5Zr Alloy

Effects of aging treatment on the precipitation behaviors and mechanical properties of Al-5.0Mg-3.0Zn-1.0Cu cast alloys

Damping Capacity Associated with Precipitation in Mg2Si/Mg–9Al Composite Materials

The Effect of Multistage Aging on Mechanical Properties and Microstructure of Forged 7050 Aluminum Alloys

Enhanced Strengthening by Two-Step Progressive Solution and Aging Treatment in AM50−4%(Zn,Y) Magnesium Alloy