Abstract:Considering the service safety for TiAl alloy under thermal shock, the effect of thermal shock temperature and cycles on micro-structural degeneration and mechanical properties were studied. The results show that the vertical decomposition of α 2 →β 0 phase transition occurs in α 2 lamellae if the single thermal shock temperature increases to 1000 °C or the thermal shock cycle increases to 10 times at 900 °C. Cracks form during the thermal shock progress as the single thermal shock temperature increases to 1000 °C or the number of thermal shocks is 5 times at 900 °C. Simultaneously, the flexural strength of samples decreases to 70% of the initial flexural strength under the same condition. It indicates that Ti–45Al–4Nb–1Mo-0.1B alloy fails as the single thermal shock temperature is above 1000 °C or the number of thermal shocks exceeds 5 times at 900 °C, and cracks generated during the thermal shock progress cause the dramatic deterioration in flexural strength. Meanwhile, the formed cracks are coarse, and the propagation path is relatively straight, which further deteriorates the flexural strength of the Ti–45Al–4Nb–1Mo-0.1B alloy. Besides, the nucleation and propagation of cracks change with the thermal shock temperature and cycles were analyzed. When the single thermal shock temperature is 1000 °C, the nucleation of cracks is not only in lamellar colony boundaries but also in α 2 /γ lamellar interfaces and the propagation path of cracks is relatively straight compared with the formation of cracks after 5 thermal shocks at 900 °C, because the thermal stress increases, and then cracks directly pass through lamellar colonies when the angle between lamellar orientation and crack propagation direction is about 90°.

Thermal Shock Properties of Ternary-Boride-Based Cladding Material

THE INTERFACE OF TERNARY-BORIDE-BASED HARD CLADDING MATERIAL

High-temperature Mechanical Properties and Thermal Shock Behavior of Ternary-Layered MAB Phases Fe2AlB2

Post-fire mechanical properties of titanium–clad bimetallic steel in different cooling approaches

Thermal shock behaviors and failure mechanisms of EB-PVD thermal barrier coatings using radiant heating

Analysis on Thermal Stress of Optimized Functionally Graded Coatings During Thermal Shock Based on Finite Element Simulation

Effect of TiC on Microstructure and Properties of Wear-Resistant Mo2FeB2 Claddings

Thermal shock behavior of nanostructured and microstructured thermal barrier coatings on a Fe-based alloy

Analysis on Phase Stability and Mechanical Property of Newly-discovered Ternary Layered Boride Cr<sub>4</sub>AlB<sub>4</sub>

Effect of surface brittle-to-ductile transition on high-temperature thermal shock resistance of Al2O3 ceramics

Effect of Fe-B Alloy on Steel Bond Hard Alloy Cladding Material

Study on the microstructure and heat affected zone of nickel-based alloy cladding layer

Phase Stability and Mechanical Property of Newly-discovered Ternary Layered Boride Cr4AlB4

Micro-structural damage and mechanical response of TiAl alloy with lamellar microstructure during thermal shock progress

Thermal shock life and failure behaviors of La2Zr2O7/YSZ, La2Ce2O7/YSZ and Gd2Zr2O7/YSZ DCL TBCs by EB-PVD

The Determining Role of Nb Interlayer on Interfacial Microstructure and Mechanical Properties of Ti/Steel Clad Plate by Vacuum Rolling Cladding.

In-situ Investigation on Deformation and Fracture Mechanism of 304/Q235 Clad Plate Produced by Hot Roll Bonding

Investigation on Mechanical Properties and Corrosion Resistance of Cobalt-Based Alloy Cladding Layer

The Improvement of the Wear Resistance of T15 Laser Clad Coating by the Uniformity of Microstructure

Influence of Heat Treatment on Microstructure and Mechanical Properties of Laser Cladding Coatings

Mechanical properties of stainless-clad bimetallic steel bars exposed to elevated temperatures