Abstract:Electrocatalytic degradation of organic pollutants is an encouraging technology for wastewater treatment. To achieve practical application, electrode plate with cost effective fabrication, high catalytic efficiency and long service life is urgently required. This work prepared a CuO-SnO2-SbOX electrode on Ti substrate, which is achieved by ultrasonic assisted deposition of Cu layer, followed by electroless deposition of SnSb layer and finalized by calcination at 500 °C. The obtained electrode (Ti/CuO-SnO2-SbOX) exhibited high catalytic degradation activity and a high oxygen evolution potential (OEP) of 2.13 V, which is 0.4 V greater than that of the widely recognized Ti/SnO2-SbOX electrode. The oxygen evolution reaction (OER) models of active oxygen intermediate adsorption was optimized by density functional theory (DFT) calculations. The results revealed that (1) the ΔG of the OER rate-determining step was raised to 2.30 eV after Cu doping on 101 plane; (2) binding energies of the optimized surface with reactive oxygen species (ROS) were substantially decreased. Furthermore, the as-prepared electrode has a high yield of hydroxyl radical generation as evidenced by terephthalic acid detection. The potential for hydroxyl radical generation was measured to be 1.8 V at pH = 12 and 2.6 V at pH = 2.The catalytic degradation rate of methylene blue (MB) follows pseudo first order reaction kinetics, and the reaction constant K value reached 0.02964 -k/min-1, twice as much as that obtained from electrodeposition electrode (Ti/Cu/SnO2-SbOX). A degradation rate of 94.6% was achieved for MB in 100 min in the first run, and the value remained over 85% in the subsequent 10 runs. At the same conditions, the degradation rate of p-nitrophenol was over 90% in 100 min and complete mineralization was achieved in 4 h.

Investigation on Preparation and Electrocatalytic Characteristics of Ti-base SnO2 Electrode with Nano-Coating

Investigation on the Electrocatalytic Characteristics of SnO 2 Electrodes with Nanocoating Prepared by Electrodeposition Method

Preparation And Characterization Of Ti/Sno2 Electrocatailytic Electrode With Nano-Coating

Dye wastewater treatment using self-made Nd doped Ti/SnO2-Sb electro-catalytic electrodes

Preparation and Characterization on Sb Doped Ti-base SnO2 Electro-Catalytic Electrodes

Preparation and Investigation of Ti-based SnO2 Electrode with an Inter Layer Containing Co Element

Effect of SnO2 addition on the service life and electrochemical properties of Ti/IrO2+Ta2O5 anodes in phenolsulphonic acid solution

Preparation and Studies on the Electrocatalytic Properties of Modified SnO2 Anodes

Study on the service life and deactivation mechanism of Ti/SnO 2 -Sb electrode by physical and electrochemical methods

Construction of TiO2 Nanotube Clusters on Ti Mesh for Immobilizing Sb-SnO2 to Boost Electrocatalytic Phenol Degradation.

A facile electroless preparation of Cu, Sn and Sb oxides coated Ti electrode for electrocatalytic degradation of organic pollutants

Study on the service life and deactivation mechanism of Ti/SnO<sub>2</sub>-Sb electrode by physical and electrochemical methods

[Effect of Heat Treatment on the Electrocatalytic Activity of SnO2/Ti Anode in Degradation of P-Benzoquinone].

Preparation and Properties of Ti/SnO2–Sb2O5 Electrodes by Electrodeposition

Fabrication Of Nano-Structured Stacked Sphere Sno2-Sb Electrode With Enhanced Performance Using A Situ Solvothermal Synthesis Method

Performance of Ti-base SnO2 Electrode with an Inter Layer Containing Mn Element

PREPARATION AND CHARACTERIZATION OF Ti-BASED Sn AND Pb OXIDES ELECTRODES

Sn-based Precursors Dependence for Electrocatalytic Degradation of Organic Pollutants on Ti/SnO2-Sb Electrode

Ti/SnO[sub 2]–sb Electrodes for Pollutant Degradation Prepared Using Ultrasonic Spray Pyrolysis

Performance And Preparation Of Ti/Sno(2)-Sb(2)O(5) Electrode By Electrodeposition

Preparation and Characterization of Dy Doped Ti-base SnO_2/Sb Electro-catalytic Electrodes