Abstract:In this paper, the effect of thermomechanical treatment process on the hardening behavior, grain microstructure, precipitated phase, and tensile mechanical properties of the new high-strength and high-ductility Al-10.0Zn-3.0Mg-2.8Cu alloy was studied, and the optimal thermomechanical treatment process was established. The strengthening and toughening mechanisms were revealed, which provided technical and theoretical guidance for the engineering application of this kind of high strength-ductility aluminum alloy. Al-10.0Zn-3.0Mg-2.8Cu alloy cylindrical parts with external longitudinal reinforcement were prepared by a composite extrusion deformation process (reciprocal upsetting + counter-extrusion) with a true strain up to 2.56, and the organizational evolution of the alloys during the extrusion deformation process and the influence of pre-stretching treatments on the subsequent aging precipitation behaviors and mechanical properties were investigated. The results show that firstly, the large plastic deformation promotes the fragmentation of coarse insoluble phases and the occurrence of dynamic recrystallization, which results in the elongation of the grains along the extrusion direction, and the volume fraction of recrystallization reaches 42.4%. Secondly, the kinetic study showed that the decrease in the activation energy of precipitation increased the nucleation sites, which further promoted the diffuse distribution of the second phase in the alloy and a higher number of nucleation sites, while limiting the coarsening of the precipitated phase. When the amount of pre-deformation was increased from 0% to 2%, the size of the matrix precipitated phase decreased from 5.11 μm to 4.1 μm, and when the amount of pre-deformation was increased from 2% to 7%, the coarsening of the matrix precipitated phase took place, and the size of the phase increased from 4.1 μm to 7.24 μm. The finalized heat treatment process for the deformation of the aluminum alloy tailframe was as follows: solution (475 °C/3 h) + 2% pre-stretching + aging (120 °C/24 h), at which the comprehensive performance of the alloy was optimized, with a tensile strength of 634.2 MPa, a yield strength of 571.0 MPa, and an elongation of 15.2%. The alloy was strengthened by both precipitation strengthening and dislocation strengthening. After 2% pre-stretching, the fracture surface starts to be dominated by dense tough nest structure, and most of them are small tough nests, and small and dense tough nests are the main reason for the increase in alloy toughness after 2% pre-stretching deformation.

Influence of Pre-Deformation on Age-Hardening Response and Mechanical Properties of Extruded Mg–6%Zn–1%Mn Alloy

Effect of Pre-Deformation on Aging Characteristics and Mechanical Properties of Mg-Gd-Nd-Zr Alloy

Effect of large pre-deformation on the microstructure, texture and mechanical properties of Al-Zn-Mg alloy extruded profiles

Strength Improvement in ZK60 Magnesium Alloy Induced by Pre-deformation and Heat Treatment

Influence of Pre-Strain on the Aging Hardening Effect of the Mg-9.02Zn-1.68Y Alloy

Effects of pre-aging on microstructure evolution and deformation mechanisms of hot extruded Mg–6Zn–1Gd–1Er Mg alloys

Study on the Aging Precipitation Behavior and Kinetics of Al-10.0Zn-3.0Mg-2.8Cu Alloy by Pre-Deformation Treatment

Effect of pre-deformation on microstructures and mechanical properties of high purity Al–Cu–Mg alloy

Microstructure and High Temperature Tensile Properties of Mg–10Gd–5Y–0.5Zr Alloy after Thermo-Mechanical Processing

Influence of cold pre-deformation on the microstructure, mechanical properties and corrosion resistance of Zn-bearing 5xxx aluminum alloy

Enhanced age-hardening of an Al-5Mg-2Zn-1Cu alloy by pre-aging combined with pre-straining

The effect of precipitation on strength and ductility in a Mg-Zn-Y alloy

Effect of Thermo-Mechanical Treatment on the Microstructure and Mechanical Properties of a Mg–6Gd–2Nd–0.5Zr Alloy

Experimental and Simulation Study for the Influence of Thermal Pre-Deformation on Subsequent Aging Precipitation Kinetics of Al-Zn-Mg-Cu Alloy

Effect of Heat Treatment on the Microstructure and Mechanical Properties of Extruded Al–4Cu–1Li–0.4Mg–0.4Ag–0.18Zr Alloy

Effects of pre-deformation on microstructure and mechanical properties of 2519A-T9I6 aluminum alloy

Effect of Heat Treatment on Dynamic Recrystallization Behaviors and Mechanical Properties of Mg–2.7Nd–0.5Zn–0.8Zr Alloy

Effect of Pre-deformation on the Precipitation Behavior and Mechanical Property of Al-Cu-Li-Mn-Zr Alloy

EFFECT OF PRE-DEFORMATION ON AGE- HARDENING AND MICROSTRUCTURE IN Al-Mg-Si-Cu ALLOY

Improving mechanical properties of ZM61 magnesium alloy by aging before extrusion

Effect secondary deformation on microstructures and mechanical properties of Mg-6Gd-3.2Y-xZn-0.5Zr extruded sheet