Abstract:Purpose This study aims to form composite solid lubricant coatings on the surface of bearing steel, which can significantly improve the tribological properties of thrust cylindrical roller bearings (TCRBs). Phosphating films possess microscopic porosity that typically needs to be sealed with oil, grease or wax. Due to its unique crystal structure, the phosphating film itself also exhibits a certain degree of lubricity. In this study, solid lubricants are used to fill the pores of the phosphating film. By combining the phosphating film with solid lubricants, lubrication and wear reduction can be achieved. Design/methodology/approach In this study, the surfaces of the shaft washer (WS) and seat washer (GS) were treated with zinc-phosphating. Subsequently, a solid lubricant solution (polytetrafluoroethylene [PTFE], MoS 2 and graphite) was sprayed onto the phosphated samples at concentrations of 1 , 2 and 3 g/L. The porous and adsorptive nature of the phosphating film was used to embed the solid lubricant particles into the film, thus forming a composite lubrication layer containing solid lubricants on the surface of the bearing steel. Findings The addition of solid lubricant materials has shown significant potential in reducing wear losses compared with phosphated samples without such additives. Increasing the amount of solid lubricant added can facilitate the formation of a transfer film, which further enhances the protective properties. However, it is important to note that excessive amounts of solid lubricant material can contribute to seizure, leading to increased wear losses of the cage and a higher average coefficient of friction (ACOF).By spraying a PTFE solution with a concentration of 2 g/L, the lowest ACOF and cage wear loss were achieved, resulting in reductions of 60.5% for the ACOF and 89.4% for the cage wear loss. Similarly, when spraying a graphite solution with a concentration of 3 g/L, the lowest wear losses for GS and WS were observed, with reductions of 51.7% for GS wear loss and 38.9% for WS wear loss. Originality/value The combination of the phosphating film and solid lubricants aims to achieve lubrication and wear reduction, providing a new approach to wear-resistant technology for TCRBs. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2023-0231/

Effect of bridged cyclotriphosphazenes as lubricants on the tribological properties of a steel-on-steel system

Effect of novel phosphazene-type additives on the tribological properties of Z-DOL in a steel-on-steel contact

Friction-reducing and antiwear behavior of metal halide-stabilized linear phosphazene derivatives as lubricants for a steel-on-steel contact

Effect of Tetraalkylphosphonium Based Ionic Liquids As Lubricants on the Tribological Performance of a Steel-on-steel System

Friction and Wear Protection Performance of Synthetic Siloxane Lubricants

Synthesis and Tribological Behavior of Ionic Liquid Substituted Fluoroalkoxycyclophosphazene Derivatives in Steel‐steel Contacts

Effect of the Chemical Structure of Fluorinated Esters on the Tribological Properties of a Steel‐on‐steel System

Synthesis and Tribological Behavior of Bridged Bicyclic Polymers As Lubricants

Tribology Study on Non-sulphur and Non-phosphorus Triazine Derivatives

Synthesis And Study On Tribological Properties Of Tri-N-Butyl Phosphorotetrathioate

Effect of composite solid lubricant coatings on the tribological performance of thrust cylindrical roller bearings

Effect of Natural Attapulgite Powders As Lubrication Additive on the Friction and Wear Performance of A Steel Tribo-Pair

Alkyloxy-s-triazine Derivatives with and Without Fluorine-Containing Substituents As Lubricants for Steel–steel Contact

Tribological evaluation of α, ω´-diimidazoliumalkylene hexafluorophosphate ionic liquid and benzotriazole as additive

Synergistic Effects between Plasma-Nitrided AISI 52100 Steel and Zinc Dialkyldithiophosphate Additive under Boundary Lubrication

The Tribological Properties of S-(1h-Benzotriazol-1-Yl) Methyl Alkyl Xanthates As Additives in Synthetic Lubricants

Tribological Behaviour of Three S-Containing Triazine Derivatives and Their Synergetic Effect with Zinc Dialkyldithiophosphate As Additives

Enhanced tribological properties of sliding contacts through the synergistic effect of PTFE film and PSAIL 2280

The Synergistic Effects of Tricresyl Phosphate Oil Additive with Chemico‐thermal Treatment of Steel Surfaces

Tribological performance of phosphonium based ionic liquids for an aluminum-on-steel system and opinions on lubrication mechanism

The Tribological Study of S‐(1H‐Benzotriazol‐1‐yl) Methyl N,N‐dialkyldithiocarbamates As Additives in Synthetic Lubricants