Abstract:Thermal and mechanical properties of SCF@SAs@SLC‐SiO2/EP composites. The demand for epoxy (EP) in semiconductor, aerospace, and other applications is currently on the rise. However, pure epoxy is difficult to meet these requirements, such as low thermal conductivity and poor toughness. Therefore, in this paper, sulfonamides (SAs) and core‐shell silica (SLC‐SiO2) were grafted onto the surface of short carbon fibers (SCF) with sizes of 0.1–6 mm by the chemical grafting method. As a result, the surface activity of SCF was improved and the interfacial properties of the EP composites were enhanced. The interfacial compatibility of SCF grafted with SAs and SLC‐SiO2 in EP is greatly improved, resulting in stronger mechanical interlocking and chemical bonding ability between EP and SCF. The results showed that when the content of SCF@SAs@SLC‐SiO2/EP composites reached 0.3 wt% of SCF@SAs@SLC‐SiO2, the impact and tensile strengths were increased from 12.15 kJ·m−2 and 43.4 MPa to 16.93 kJ·m−2 and 74.97 MPa compared with the pure epoxy, which were improved 39.3% and 72.7%. In addition, the thermal conductivity of SCF@SAs@SLC‐SiO2/EP composites was also improved by 12.5% from 0.205 W·(m·K)−1 to 0.2306 W·(m·K)−1 compared with the pure EP. This is due to improved chemical interactions and mechanical interlocking at the fiber‐epoxy interface. This study provides a new method for the preparation of high‐performance SCF/EP composites. Highlights The amino group of sulfonamides was grafted with short carbon fiber to increase the surface active group of short carbon fiber. Sulfonamides react with carboxyl groups on the surface of core‐shell silica to form an "organic–inorganic" structure. Improve the surface roughness of short carbon fiber, and make it evenly dispersed in epoxy resin, so as to improve the performance of epoxy composite materials.

Morphology and Properties of ACS/Ultrafine Sb_2O_3 Composites

Influence of Preparation Method on Property of ACS/Sb2O3 Composite

Mechanical Properties and Microstructure of Calcium Sulfate Whisker-Reinforced Cement-Based Composites

Mechanical property and thermal stability of short carbon fiber reinforced polysulfonamide composites

Enhanced Interfacial, Mechanical, and Anti-Hygrothermal Properties of Carbon Fiber/cyanate Ester Composites with the Catalytic Sizing Agents of Titanium Epoxy

Effects of High Temperature and Substitution Rates of Fly Ash on the Mechanical Properties and Microstructures of Steel-Basalt Hybrid Fibers Reinforced Cementitious Composites

Thermal Stability, Smoke Emission and Mechanical Properties of Poly(vinyl Chloride)/hydrotalcite Nanocomposites

Effect of Rare Earth Oxide Addition on the Microstructure and Properties of Ultrafine Grain W-20Cu Composites

Study on combustion property and synergistic effect of intumescent flame retardant styrene butadiene rubber with metallic oxides

The Effect Of Morphology On The Flame-Retardant Behaviors Of Melamine Cyanurate In Pa6 Composites

STUDY ON BIOCERAMIC COMPOSITE MATERIALS

Enhancing the Mechanical Properties of Basalt Fiber and Stainless Steel Wire Mesh Composites Incorporating Fire Retardants Through Response Surface Methodology Optimization

Preparation and flame ablation/oxidation behavior of ZrB2/SiC ultra-high temperature ceramic composites

Construction of "organic–inorganic" hierarchical structure of carbon fibers and the effect on the properties of epoxy composites

Styrene-butadiene-styrene Copolymer Compatibilized Carbon Black/polypropylene/polystyrene Composites with Tunable Morphology, Electrical Conduction and Rheological Stabilities.

Ultrafine Grained Bulk Ceramic Composites Consolidated from Nanostructured Composite Powders by Pressure Less Sintering

Preface for Special Issue ‘composites Part B’: Flame Retardants and Flame-Retardant Polymers/composites

Rheological, flame retardancy, and thermomechanical properties of polymethyl methacrylate composites: Effects of flame retardant and toughener

Effects of Metal Binder Content and Carbide Grain Size on the Microstructure and Properties of SPS Manufactured WC–Fe Composites

Microstructure evolution and mechanical properties of Al-Al2O3 composites fabricated by selective laser melting

Cyanate Ester/Functionalized Silica Nanocomposite: Synthesis, Characterization and Properties