Abstract:Groove surface textures with different orientations and spacings were prepared on the Ti–6Al–4V alloy by using a laser. Fretting tests (rubbed with a Ti–6Al–4V ball) were conducted under different textures, and the coefficient of friction (COF) curves, system deformation and wear morphologies were analysed in detail. The groove orientations to the fretting direction affected the fretting wear behaviour through the following ways: (1) Fretting tests on different groove orientations resulted in different fretting loop shapes at the initial stage of fretting wear. (2) The COF curves of fretting test on perpendicular grooves and 45° grooves were similar. COF presented a sharp increase after approximately 1000 cycles under relatively low loads. The COF curves of fretting test on parallel grooves and untextured surface were similar. Only a small oscillation of COF was observed during the whole fretting tests. (3) When fretting was run in gross slip regime, the magnitude of system deformation was perpendicular grooves, no-texture samples, 45° grooves, and parallel grooves in order. The above results may have resulted from the influence of surface textures on the formation and development of wear debris. For the perpendicular grooves, high pressure was recorded in partial slip regime cracks, and peeling appeared on the convex platform of samples with the groove spacing of 80 μm, and this phenomenon promoted the formation of debris. Moreover, the perpendicular grooves prevented debris from spilling out of contact areas. For the parallel grooves, the filling mechanism of grooves was found, in which the material in the upper layer gradually squeezed the material in the lower layer toward the centre and bottom of the groove, and the parallel grooves accelerated debris from spilling out of contact areas. Therefore, groove surface textures may adjust the fretting regime of titanium alloys by changing the orientation and spacing, which could provide a new tribology design for fretting friction pairs.

Fretting Wear of Carburized Titanium Alloy Against ZrO2 under Serum Lubrication

Contact damage failure analyses of fretting wear behavior of the metal stem titanium alloy-bone cement interface

Preparation and Study on Fretting Tribological Behavior of Composite Lubrication Structure on the Titanium Alloy Surface

The synergistic influence of the intravascular starling forces on pulmonary microvascular solute flux in human ARDS.

A tribological investigation of SLM fabricated TC4 titanium alloy with carburization pre-treatment

Revealing the composite fretting-corrosion mechanisms of Ti6Al4V alloy against zirconia-toughened alumina ceramic in simulated body fluid

Variable cycle fretting conditions meditated wear behavior and mechanism in a self-lubricating composite coating on TC21 titanium alloy substrate

Wear and surface degradation of commercial ZTA femoral heads under boundary lubrication conditions

Factors associated with HIV infection among sexually experienced adolescents in Africa: a pooled data analysis

Tribological Behavior of Ti-6Al-4V Against Cortical Bone in Different Biolubricants.

Biotribological properties at the stem-cement interface lubricated with different media

The oil lubricated fretting wear behavior under different sliding displacements and frequencies of Ti6Al4V titanium alloy as affected by micro-shot peening

Ti-6Al-4V fretting wear and a quantitative indicator for fretting regime evaluation

Effect of ultrasonic surface rolling on surface layer properties and fretting wear properties of titanium alloy Ti5Al4Mo6V2Nb1Fe

Dependence of fretting wear on the microstructure characteristics and impact on the subsurface stability of a metastable β titanium alloy

Influence of Ball Burnishing on Lubricated Fretting of the Titanium Alloy Ti6Al4V

Tribological Properties of Ti6Al4V Alloy Composite Texture Fabricated by Ultrasonic Strengthening Grinding and Laser Processing

Experimental Study on the Wear Characteristics of Textured Joint Surfaces under Bionic Lubrication

Friction and wear of titanium alloys sliding against metal, polymer, and ceramic counterfaces

Fretting wear evolution of γ-TiAl alloy

Effect of groove surface texture on the fretting wear of Ti–6Al–4V alloy