Abstract:The effects of strain rate on the shear fracture behavior of Sn3.0Ag0.5CuiCu solder joints with thin and thick interfacial intermetallic compound layers were investigated. A single lap-shear sample was designed to conduct the study. The Cu/Sn3.0Ag0.5Cu/Cu joints were reflowed at 250 degrees C and 280 degrees C for 10 min, respectively, resulting in formations of a thin (6.08 mu m) and thick (13.25 mu m) intermetallic compound layer between the solder and Cu substrate. The single lap-shear tests were performed at the shear strain rates of 5 x 10(-4) s(-1), 5 x 10(-3) s(-1), 2 x 10(-2) s(-1), 1 x 10(-1) s(-1) and 2 x 10(-1) s(-1) to observe the shear fracture behavior. Experimental results revealed that both the thickness of the interfacial inter metallic compound layer and strain rate had influence on the shear strength and failure mode of the solder joint. The shear strength of the solder joints increased with increasing strain rate, but decreased with thickness of the interfacial intermetallic compound layer. It was observed that the solder joints broke in a ductile manner at low strain rates (5 x 10(-4) s(-1), 5 x 10(-3) s(-1)), although they exhibited a ductile-brittle mixed manner at intermediate (2 x 10(-2) s(-1)) and a brittle manner at high strain rates (1 x 10(-1) s(-1), 2 x 10(-1) s(-1)). In the case of low strain rates, the ductile fracture behavior of joints with thin and thick intermetallic compound layers were similar. Nevertheless, more cleavage and broken Cu6Sn5 grains were detected on the fracture surface of the solder joint with a thick intermetallic compound layer as the strain rate increased to 2 x 10(-2) s(-1), 1 x 10(-1) s(-1) and 2 x 10(-1) s(-1). Furthermore,, when the strain rate of 2 x 10(-1) s(-1) was applied, the solder joint with a thin intermetallic compound layer was completely broken inside the Cu6Sn5 layer, but partly broken at the Cu6Sn5/Cu3Sn interface for the joints with a thick intermetallic compound layer. Four modes were proposed to explain the detailed ductile-to-brittle transition in failure behavior. In addition, the strain rate sensitivities of the solder joints with thin and thick interfacial intermetallic compound layers were also investigated. It was found that the strain rate of a solder joint with a thick interfacial intermetallic compound layer was lower than that of one with a thin interfacial intermetallic compound layer. (C) 2016 Elsevier B.V. All rights reserved.

In-situ Observation on Microfracture Behavior Ahead of the Crack Tip in 63sn37pb Solder Alloy

Experimental and Statistical Study of the Fracture Mechanism of Sn96.5Ag3Cu0.5 Solder Joints via Ball Shear Test

Inconsistent creep between dendrite core and interdendritic region under different degrees of elemental inhomogeneity in nickel-based single crystal superalloys

The In-Situ Observation of Microstructure, Grain Orientation Evolution and Its Effect on Crack Propagation Path in SAC305 under Extreme Temperature Changes

Cracking in a Fe–25Mn–3Si–3Al Steel

In situ observation of intergranular fracture propagation in nanocrystalline freestanding ultrathin tungsten film

In-situ study of creep in Sn-3Ag-0.5Cu solder

In-situ observation of crack propagation through the nucleation of nanoscale voids in ultra-thin, freestanding Ag films

Fracture pattern evolution of SnAgCu–SnPb mixed solder joints at cryogenic temperature

The microstructure evolution and failure mechanism of Sn37Pb solder joints under the coupling effects of extreme temperature variation and electromigration

Fracture Behavior of Sn-3.5Ag-0.7Cu and Pure Sn Solders as a Function of Applied Strain Rate

SEM in situ study on high cyclic fatigue of SnPb-solder joint in the electronic packaging.

The In-Situ Observation of Grain Rotation and Microstructure Evolution Induced by Electromigration in Sn-3.0Ag-0.5Cu Solder Joints

Study on the Influence of Defects on Fracture Mechanical Behavior of Cu/SAC305/Cu Solder Joint

In-Situ Sem Observation on Fracture Behavior of Austempered Silicon Alloyed Steel

Crack mechanism correlated with Sn grain orientations on Ni metal surface subjected to 1000 thermal shocks

Ductile-to-brittle transition in fracture behaviors of common solder alloys over a temperature range down to −150 °C

Shear Strength and Fracture Behavior of Reflowed Sn3.0ag0.5cu/Cu Solder Joints under Various Strain Rates

In-situ electron backscatter diffraction of thermal cycling in a single grain Cu/Sn-3Ag-0.5Cu/Cu solder joint

Shear Strengths and Fracture Behaviors of Cu/Sn37Pb/Cu Soldered Joints Subjected to Different Displacement Rates

In Situ SEM Observation of Microscale Strain Fields Around a Crack Tip in Polycrystalline Molybdenum