Abstract:The multilayer graphene (MLG) reinforced WC-10Ni 3 Al cemented carbide was prepared by microwave sintering. The effects of the sintering temperature and MLG content on the microstructure and mechanical properties of the WC-10Ni 3 Al cemented carbide were investigated. The promotion effect and strengthening mechanism of MLG on WC-10Ni 3 Al by microwave sintering were explored. The tribological properties of WC-10Ni 3 Al and Ti6Al4V(TC4) were studied, and the wear mechanism of WC-10Ni 3 Al was revealed. The experiment result show that the WC-10Ni 3 Al-0.5 wt.% MLG sample sintered at 1450°C had its greatest mechanical properties with a relative density of 96.9%, hardness of 1430 HV, flexural strength of 1410 MPa and fracture toughness of 15.7 MPa·mm 1/2 , which were 4.2%, 12.2%, 24.4%, and 29.6% greater than those of the sample without MLG added, respectively. The reinforcing and toughening mechanisms of adding MLG in WC-10Ni 3 Al samples consist of fine crystal strengthening, crack bridging and deflection, MLG pulling out and bridging. The results of friction experiment show that the friction coefficient and wear rate of the WC-10Ni 3 Al samples were lower than those of YG8 (WC-8 wt. % Co cemented carbide). The WC-10 Ni 3 Al-0.5 wt.% MLG sample obtained the lowest friction coefficient of 0.35 and the lowest wear rate of 1.69 × 10 -5 mm 3 N -1 m -1 . A stable solid lubrication film was produced on the friction surface of the WC-10Ni 3 Al samples, which was conducive to reducing the breakage and wear of WC grains. MLG can enhance the stability of solid lubrication film and reduce its friction coefficient.

Carbon Content's Effects on the Structure and Properties of Micro-waved Sintering Sub-micron Cemented Carbide

Effect of carbon content on the microstructure and properties of Cr-doped WC–15Co cemented carbide

Preparation and mechanical properties of SiCw-reinforced WC-10Ni3Al cemented carbide by microwave sintering

Effect of carbon content on the properties of inhomogeneous cemented carbides with fine-grained structures produced via one-step transformation

Role of Co Content on Densification and Microstructure of WC–Co Cemented Carbides Prepared by Selective Laser Melting

Preparation of WC-Co Cemented Carbide by Spark Plasma Sintering: Microstructure Evolution, Mechanical Properties and Densification Mechanism

Investigation of TiC formation during ball-milling of elemental titanium and carbon

Microstructure and properties of ultrafine WC–Co–VC cemented carbides with different Co contents

Mechanical Properties and Microstructural Behaviour of Microwave Sintered WC–Co

Comparative Study on Microstructure and Mechanical Properties of Coarse-grained WC-based Cemented Carbides Sintered with Ultrafine WC or (W+C) as Additives

Microstructure and mechanical properties of oscillatory pressure sintered WC ceramics with different carbon sources

Effects of SiC addition on microstructure and properties of WC–6Co cemented carbide prepared by SPS

EFFECT OF MICROWAVE IRRADIATION ON GRAPHITIZATION OF CARBON MATRIX IN PULVERIZED COAL

Microstructure, mechanical and tribological properties of multilayer grapheme reinforced WC-10Ni 3 Al prepared by microwave sintering

Effect of Graphene on the Microstructure and Mechanical Properties of WC-Based Cemented Carbide

Effect of Metal Elements on Microstructure and Mechanical Properties of Ultrafine Cemented Carbide Prepared by SPS

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

Combined effect of SiC and carbon on sintering kinetics, microstructure and mechanical properties of fine-grained binderless tungsten carbide

Effects of micro/nano CeO2 on the microstructure and properties of WC-10Co cemented carbides

Fabrication of Diamond-WC-Based Cemented Carbide Composites by Microwave Sintering

Microstructure and properties of WC-Co/CrMnFeCoNi composite cemented carbides