Abstract:The flow condensation heat transfer coefficient of R134a inside two helical micro-fin tubes with outer diameter of 6.35 mm and helical angles of 18o and 28o respectively were experimentally studied at a high mass flux ranging from 500 to 1100 kg m−2 s−1. The condensation temperatures are 35°C, 40°C and 45°C, and the vapor qualities ranges from 0.95 to 1.00 at the inlet section and from 0.00 to 0.05 at the outlet section. Experimental results show that there are annular and intermittent flow regimes inside the tube under experimental conditions, the ratio of annular flow region to the total heat transfer region is about 70%. The liquid film flow changes from rotational flow to coexistence of rotational and horizontal flows when the vapor quality is 0.475±0.08, 0.486±0.06 and 0.521±0.05, respectively and the corresponding saturation temperature is 35°C, 40°C and 45°C. Based on the experimental data, the heat transfer coefficient increases with increasing mass flux and fin helical angle, and with decreasing saturation temperature and Reynolds number of cooling water. In addition, the heat transfer coefficient of annular flow is greater than that of intermittent flow, in other words, the heat transfer coefficient increases with increasing vapor quality. The heat transfer coefficient obtained at high mass flux was compared with the calculated data of some published correlations used at low mass flux. It was found that most correlations underestimate the experimental heat transfer coefficient inside the micro-fin tube, and these prediction deviation increases with increasing mass flux and fin helical angle. By introducing some dimensionless numbers as well as considering the flow mechanism of liquid film inside the tube, two heat transfer coefficient correlations were proposed based on the experimental data. The ratio of liquid film thickness to fin height was used to characterize whether the liquid film flow is rotational flow or coexistence of rotational and horizontal flows in the proposed correlation, which shows a better prediction accuracy with a mean deviation of less than 7.3%.

EVAPORATION AND CONDENSATION HEAT TRANSFER IN HORIZONTAL MICRO-FIN TUBES

Flow Condensation Heat Transfer and Pressure Drop in Horizontal Micro-Fin Tubes

Experimental Investigation of Evaporation Heat Transfer Inside Horizontal Micro-Fin Tubes

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

Theoretical and Experimental Analyses of Two-Phase Flow Condensation Heat Transfer Inside the Horizontal Micro-Fin Tube

Two-Phase Flow Heat Transfer In Micro-Fin Tubes

Correlation of Evaporation Heat Transfer Inside 8.8 Mm and 7.14 Mm Horizontal Round Micro-Fin Tubes

Heat transfer and pressure drop during condensation of R22 in microfin tubes

Condensation Heat Transfer and Pressure Drop of R22 in 5-Mm Diameter Microfin Tubes

Heat Transfer And Pressure Drop During Evaporation Of R22 In Micro-Fin Tubes

R410A and R32 condensation heat transfer and flow patterns inside horizontal micro-fin and 3-D enhanced tubes

Condensation Pressure Drop and Heat Transfer in 5-Mm-od Micro-Fin Tubes

Condensation and Evaporation Heat Transfer Characteristics in Horizontal Smooth and Three-Dimensional Enhanced Tubes

Experimental Investigation of Condensation in Micro-Fin Tubes of Different Geometries

Heat Transfer Performance of Microfin Tubes and -Three-dimensional Heat Transfer Tubes

Condensation and Evaporation Heat Transfer Characteristics of Low Mass Fluxes in Horizontal Smooth Tube and Three-Dimensional Enhanced Tubes

A Numerical Investigation of Convective Condensation in Micro-Fin Tubes of Different Geometries

Convective Condensation Inside Horizontal Smooth and Microfin Tubes

Single Phase And Two Phase Flow Characteristics And Heat Transfer In Micro-Fin Tubes

Evaporation Heat Transfer and Pressure Drop of R161 in A 7 Mm Micro-Fin Tube

Influence of 0° Helix Angle Micro Fins on Flow and Heat Transfer of R32 Evaporating in a Horizontal Mini Multichannel Flat Tube