Abstract:Immediate implant placement (IIP) has garnered significant attention due to its minimally invasive approach and ability to facilitate immediate crown replacement. Nevertheless, challenges persist in processing complex geometries and selecting suitable materials. This study successfully fabricated high-performance, complex-structured (Ce, Y)-TZP-based composite ceramics using vat photopolymerization (VPP) technology, combining second-phase strengthening and grain boundary segregation effects. The incorporation of α-Al 2 O 3 as a secondary phase led to a progressive refinement of (Ce, Y)-TZP grains, with the most favorable grain size achieved at 20 wt% α-Al 2 O 3 , reducing the average grain size to 0.75 μm. However, excessive α-Al 2 O 3 content resulted in micropore formation, compromising the material's mechanical performance. At an optimal concentration of 15 wt% α-Al 2 O 3 , the composite exhibited superior mechanical properties, including a Vickers hardness of 11.53 ± 0.27 GPa and a flexural strength of 525.5 ± 21.3 MPa. Despite these improvements, some coarse (Ce, Y)-TZP grains persisted within the ceramic matrix. To further enhance grain refinement at lower α-Al 2 O 3 content, a minimal addition of La 3+ (0.1 wt%) was introduced, promoting grain boundary segregation and additional grain refinement. This modification reduced the (Ce, Y)-TZP grain size to 0.74 μm, increased hardness to 13.03 ± 0.31 GPa, and elevated flexural strength to 550.4 ± 39.8 MPa, while maintaining excellent material stability.

Microstructure and Mechanical Properties of Ce-Y-TZP Ceramic Composites for Ceramic Plunger and Ball Valve

Preparation of CePO4-coated Zirconia Ceramics and Their Mechanical Behavior

Second Phase Strengthening and Grain Boundary Segregation Effects on the Microstructure and Properties of (Ce, Y)-TZP-Based Ceramics Prepared by Vat Photopolymerization

Phase and microstructure evolution of 0.2Zr1-Ce O2/Zr1-Ce SiO4 (0 ≤ x + y ≤ 1) ceramics designed to immobilize tetravalent actinides

Regulating mechanical and anti-erosion wear properties of ZTA ceramics by adjusting Y2O3 content

Mechanical properties and low temperature degradation (LTD) of cation-stabilized zirconia

Phase transformation of Y-Ce-TZP/Al2O3 composite ceramic annealed in air

The Effect of Sintering Temperature on Phase-Related Peculiarities of the Microstructure, Flexural Strength, and Fracture Toughness of Fine-Grained ZrO2–Y2O3–Al2O3–CoO–CeO2–Fe2O3 Ceramics

Thermophysical and mechanical properties of cubic, tetragonal and monoclinic ZrO2

Thermal and mechanical properties of Sc2O3–CeO2 co-stabilized zirconia ceramic as promising thermal barrier coating material

Tribological properties and wear resistance mechanism of WC-ZrO2-Al2O3 ceramics

Research of Structural, Strength and Thermal Properties of ZrO2—CeO2 Ceramics Doped with Yttrium

Preparation of Cepo4 Modified Zro2 Ceramics with Different Particle Sizes and Their Mechanical Behaviors

Effects of ZrB2 on Mechanical Properties of Al2O3-ZrB2-SiC Composite Ceramics at Room Temperature

Enhancement of thermal shock and slag corrosion resistance of MgO–ZrO2 ceramics by doping CeO2

Effect of Yb Substitution on Microstructure, Physical and Mechanical Properties of Negative Thermal Expansion Zr1−xYbxWMoO8−x/2 (x = 0–0.05) Ceramic

Crystal structure, Raman spectroscopy, metal compatibility and microwave dielectric properties of Ce2Zr3(MoO4)9 ceramics

Stronger and Tougher Nanosized Dense Ceria-Doped Tetragonal Zirconia Polycrystals by Sinter-Hip

Microstructure and properties of SrTiO3/ZrO2 ceramic composites prepared through pressureless sintering

Preparation and properties of ternary rare earth co-stabilized zirconia ceramics for dental restorations

Preparation and Characterization of Fibrous Alumina and Zirconia Toughened Alumina Ceramics with Gradient Porosity