Abstract:As a new element of flame, tubular flame especially the swirl type has excellent flame characteristics such as negligible heat loss, aerodynamic stability and thermodynamic stability. The premixed swirl type tubular flame has been extensively studied through a variety of burners, and various applications have been proposed and demonstrated for determining the flammability limits, stabilizing a flame in a high speed flow, and obtaining a uniform and large-area laminar flame to heat iron slab or to reduce steel sheet surface. To avoid potential hazards of flame flash back even detonation in premixed mode, an inherently safe technique of rapidly mixed tubular flame combustion has proposed, in which the fuel and the oxidizer are individually and tangentially injected into a cylindrical burner from four rectangular slits. Recently this burner has been successfully adopted to investigate the characteristics of oxygen enhanced combustion of methane, which provides a useful tool to save energy and reduce emissions. The results illustrate that the mixing of fuel and oxidizer plays a vital role in obtaining a stable tubular flame. To fundamentally investigate the flow field especially the mixing process in the rapidly mixed tubular flame burner, a series of measurements have been made on the flow visualization and velocity distribution with a Particle Image Velocimetry (PIV) system. Two groups of optically accessible quartz burners were designed: in the first group, the width of the rectangular slit was maintained as 2 mm while the length varied from 8 to 64 mm, in which the swirl number (Sw) varied from 2.75 to 0.34; in the second group, the slit width increased from 1 to 3 through 2 mm while maintaining the slit length as 8 mm, in which the swirl number decreased from 5.89 to 1.70 through 2.75. The total flow rate and the mean injection velocity ratio of fuel inlet to oxidizer inlet were also varied to measure the mixing layer thickness through flow visualization in a cross section perpendicular to the tube axis around the center of the burner. Detailed observation shows that the mixing layer thickness around the inlet is dominated by a boundary layer type flow regardless of swirl number and injection velocity ratio. The coefficients for the thickness estimation based on the square root of injection velocity (in reverse relationship) have been summarized. In addition, for a constant total flow rate, the mixing is fastest when the mean injection velocity of each inlet is the same. The flow visualization and the axial velocity distribution in a plane containing the tube axis were also analyzed to illustrate the flow motion downstream of the injection slits. The results demonstrate that a reverse flow appears in the burners of swirl number larger than 0.60.

The Influence of Air Distribution on the Single-Phase Flow Field of Central Fuel Rich Swirl Burner

The Effect of Inner Secondary Air on the Flow Field of a Swirl Burner

TEST STUDY ON OUTLET FLOW FIELD PERFORMANCE FROM WAVE-SHAPED COMBUSTION-STABILIZING BODY OF THE CONCENTRATION TUNABLE RICH/LEAN BURNERS

Experimental and Numerical Study of a Two-Stage Swirl Burner

Observations on the mixing process between an inner cold air stream and an outer swirling tubular flame stream

Experimental study on cold two-phase flow in swirl burner exit

INFLUENCE OF SECONDARY AIR STRAIGHT FLOW VELOCITY IN THE SWIRL BURNER UPON FORMATION OF Nox

Experimental study on combustion flow field characteristics of swirl combustor

Analysis of the Mixing Between Primary Air and Secondary Air in a Low NOx Swirl Burner

Cold Model Experimental Study on the Concentrated Dual Register Swirl Burner

Effects of Swirl on the Heating Process of a Central Gas Stream in a Tubular Flame

Numerical Simulation for Effects of Venturi Tube on Swirling Flow Field

Numerical Simulation for Swirl Jet Flows to Change of Flaring Angle of Primary Air Tube

Experimental Measurement of Gas-Solid Two-Phase Flow of a Swirl Burner by Optical Wave Method

Experimental study on the effect of particle size on the exit flow field of a swirl burner

Isothermal swirling flow characteristics and pressure drop analysis of a novel double swirl burner

The effects of swirl number on the combustion characteristics in an internally-staged combustor

Effect of swirl number on the number of particle impacts near a swirl burner outlet

An Experimental Study on the Flow Visualization in Rapidly Mixed Tubular Flame Burners of Various Swirl Numbers

EXPERAMENTAL STUDY ON FLOW FIELD BEHAVIOR CONCERNING THE CROSSED JET FLOWS OF MICRO-SWIRLING PRIMARY AIR AS WELL AS UPPER AND LOWER SECONDARY AIR

Numerical investigation of inlet guiding ring effect on combustor flow field with multiple swirler structures