Abstract:Objective To evaluate the clinical significance of the lower extremity CT parameters in total knee arthroplasty ( TKA) .Methods The clinical data of the patients undergone primary TKA in the department of joint surgery of the First Affiliated Hospital of Sun Yatsen University , were reviewed between January, 2014 and November, 2015.Inclusion criteria:the knee osteoarthritis patients undergone primary TKA and operated by the same surgeon; the clinical data were integrated as well .Exclusion criteria:the patients with rheumatoid arthritis history , knee infection or surgical histories;lower extremity skeletal deformity or other deformity except the knee joint; combining with severe medical diseases that affected the functional rehabilitation . Forty-seven patients ( 56 knees ) were included in this study [including 39 females(45 knees) and eight males (11 knees)], of which 19 cases (22 knees) were analyzed by preoperative CT parameters to guide the TKA (the modified group ) and 28 cases (34 knees) adopted traditional procedures only ( the traditional group ) .The average age was 67.9 years ( range 51-81 years) .The following indices were collected: operation time, intraoperative blood loss, postoperative drainage and postoperative complications .The preoperative and postoperative mechanical alignments of lower extremity were analyzed to compare the alignment improvement between the two groups ; the Knee Society knee score ( KSS) was applied to evaluate the early recovery of the patients .Independent sample t test was performed to analyze the data complied with the normal distribution and Mann-Whitney U test was adopted to analyze the data with abnormal distribution .The differences of pre-and postoperative KSS scores of one group were compared by paired t test.The enumeration data were compared by the Chi-square test. Results The accuracy of lower extremity alignment reconstruction of modified group were 90.9%and that of the traditional group were 67.6%, showing significant differences between the two groups (χ2 =3.982, P <0.05).The accuracy of femoral components installment of the modified group was 95.5%, which was higher than that of the traditional group (70.2%) (χ2 =5.139, P <0.05).The accuracy of tibial components installment of the modified group was 95.5%and 94.2%in the traditional group;no statistical difference was found .Compared with the traditional group , the amount of intraoperative blood loss of the modified group decreased (Z=-3.673, P<0.000).However, the operation time (Z =-1.307,P>0.05), postoperative drainage (Z =-0.260, P>0.05) and complications (χ2 =0.078, P>0.05) showed no statistical differences .Compared with pre operative scores , the postoperative KSS scores were significantly improved in both groups ( P <0.05 ) , but no significant difference was found between the groups after the surgery ( t =Z0.360, P >0.05 ) .Conclusion The application of lower extremity CT parameters in the primary total knee arthroplasty is beneficial in reconstructing the coronal alignment and acquiring fine component positions;the preoperative planning parameters of lower extremity CT are useful for guiding TKA surgeries .

The Geometry Parameters Measurement in the Computer Aided Knee Replacement Surgery System

Reconstruction and Optimization of the 3D Geometric Anatomy Structure Model for Subject-Specific Human Knee Joint Based on CT and MRI Images

Femoral valgus angle measurement in Three-dimensional reconstruction Virtual environment based on CT images

Measurement of femoral posterior condylar offset and posterior tibial slope in normal knees based on 3D reconstruction

Computer-Assisted Knee Surgical Navigation

An automatic measurement system of distal femur morphological parameters using 3D slicer software

Automating Analyses of the Distal Femur Articular Geometry Based on Three-Dimensional Surface Data

[Determination of Femoral Anatomic Axis in Robot-Assisted Surgery of Total Knee Replacement].

3D Measurement of Anatomic Parameters and Development of a Digital Design to Improve the Outcome of Lower-Extremity Surgery

Prosthetic matching of knee valgus for total knee arthroplasty: three-dimensional digital measurement and analysis

Femoral coordinate system based on articular surfaces: Implications for computer-assisted knee arthroplasty

Scheme to Extract Femur Axes Automatically Based on CT Images

An Approach to Automated Measuring Morphological Parameters of Proximal Femora on Three-Dimensional Models.

The construction of three-dimensional finite element model of TKA knee

Guidelines for Instrumentation for Total Knee Replacement Based on Frontal Plane Radiographs.

An Imaging Measurement Study of Normal Knee Parameters in Southeast China.

Construction of a three-dimensional finite element model of total knee prosthesis

Estimation Of The Relative Pose Of The Femoral And Acetabular Components In A Visual Aided System For Total Hip Replacement Surgeries

Application of three-dimensional CT reconstruction in total knee arthroplasty

Application analysis on CT parameters of lower extremities in primary total knee arthroplasty

PATIENT-SPECIFIC 3D RECONSTRUCTION OF A COMPLETE LOWER EXTREMITY FROM 2D X-RAYS: A CADAVERIC VALIDATION STUDY